A faulty transmission control module (TCM) most often causes limp mode with the gearbox stuck in one gear, harsh jolts when you select D or R, erratic gear changes, flashing PRND letters and a gearbox or engine warning light. However, the same symptoms are often caused by a low gearbox oil level, a weak battery, a poor earth or a faulty sensor. To test a transmission control module, start by checking the battery and reading the fault codes with a diagnostic tool that can talk to the gearbox control unit, then check the power supply, the connector, the oil and the live data. Below we explain the symptoms, the diagnostic steps and what the most common fault codes mean.
Engine Control Unit Volkswagen, Skoda 1.8 T Bosch 06A906032DJ 0261206864
Vendors's code: 0261206864
Product code: 0261206864
Barcode:
Code 39:
ISBN:
Select a product option:
Individual variants may differ in price
product option
Important: Depending on the ECU type and vehicle model, not all of the options listed below may be available.
To select the correct option for your vehicle and ECU, please contact us before purchasing:
contact@auto24parts.com
1. Locked
This option is intended for professional workshops with the required specialist equipment and technical knowledge.
The ECU has been removed from a vehicle intended for recycling and still contains the immobilizer data and other information from the previous vehicle. Before it can be used in another car, it must be unlocked and then programmed using specialist automotive diagnostic equipment.
2. Unlocked
Several preparation methods may be available. The possible options depend on the ECU type, vehicle model and immobilizer system. Please contact us before purchasing, as some preparation methods are not available for every ECU.
Our electronics specialists can prepare the ECU in one of the following ways:
a) ECU with PIN code (Car Pass)
The PIN code is supplied, but programming with a suitable diagnostic tool is still required. After installing the ECU, it must be reset using the supplied PIN code and then programmed to the vehicle’s immobilizer system.
b) VIRGIN ECU
The data from the previous vehicle is removed and the ECU is restored to a clean, factory-like state. After installation, it must be programmed to the vehicle using a compatible specialist diagnostic tool. Unless another preparation method is specified in the product description, this is the standard unlocking option for most of our ECUs.
c) Plug & Play – IMMO OFF
The immobilizer function is disabled in the ECU. After installation, the engine can start without additional immobilizer programming. Please note that the vehicle will no longer have an active immobilizer function, and an immobilizer warning light or fault code may remain, depending on the vehicle model.
d) Plug & Play – Automatic Programming
After installation, the ECU automatically learns and saves the required vehicle data. No additional programming is normally required.
e) Plug & Play – 1:1 Clone
The data from your original ECU is copied to another fully functional ECU. The cloned unit is then ready for installation without additional programming.
You must send us your original ECU so that we can transfer its data to the replacement unit.
The original ECU must have working communication with the vehicle, a diagnostic tool or our programming equipment. If the required data cannot be read, a complete 1:1 clone may not be possible.
3. Complete Plug & Play Set
A complete matched set containing the ECU, immobilizer components and all other parts required to start the vehicle without additional programming. All components supplied in the set must be installed in the vehicle.
Important:
Dispatch time depends on the selected option. If an unlocked or specially prepared version is ordered, the preparation service usually requires an additional 1–2 business days.
Ask about the product
Administratorem danych osobowych jest Auto24parts. Przetwarzamy je w celu przesłania odpowiedzi na zapytanie. Więcej informacji dotyczących przetwarzania danych osobowych znajduje się w polityce prywatności.
Price 30 euros applies shipments to 5 kg on worldwide. Above this weight, please contact us by email to check price
Shipping cost for the selected product
The shipping cost applies to this product (in the selected variant - if applicable). It may change after adding other products to the cart.
Looking for a 06A906032DJ ECU for a 1.8 T engine?
This used Bosch unit in working order (0 261 206 864) comes from a Volkswagen or Skoda with the 1.8 T petrol engine. Before buying, compare both numbers with the label.
Engine Control Unit Volkswagen, Skoda 1.8 T Bosch 06A906032DJ 0261206864
The turbocharged 1.8 T engine needs precise control of injection, ignition and boost pressure. In Volkswagen and Skoda models, one of the units responsible for this is the Bosch ECU with VW number 06A906032DJ. Its number, 0 261 206 864, belongs to the Bosch series intended for petrol engines.
Numbers to compare
- 06A906032DJ – VW part number
- 0261206864 – Bosch number, shown on the label as 0 261 206 864
The DJ suffix denotes the software or hardware version. 06A906032 ECUs with other letters look similar but may contain different data.
When to suspect the ECU
- the engine won't start and the fuel pump doesn't run,
- the engine warning light is on and there is no communication with the tester,
- rough running and misfires not caused by the spark plugs or coils,
- signs of water damage or corrosion on the circuit board or connector.
First rule out a fault in the wiring loom, earths and power supply – the most common causes of similar symptoms.
ECU option
We offer two options. The first is an unlocked ECU – prepared by us before dispatch (usually 1–2 working days). The second is a locked ECU, with the data and immobiliser of the previous car, for workshops that carry out unlocking, programming and matching themselves.
The possible unlocking method – PIN / CAR PASS, Virgin, IMMO OFF, auto programming or cloning – is determined case by case, as it depends on the part number, software and immobiliser. For the 06A906032DJ we will confirm it before you buy. See also: ECU preparation options.
Questions and answers
| Does it fit the non-turbo 1.8? |
|---|
| This unit comes from a 1.8 T engine. We don't recommend it for a different engine without checking the numbers – please ask us before buying. |
| How long does it take to prepare the unlocked version? |
| Usually 1–2 working days before the parcel is sent. Beforehand, we confirm which unlocking method is possible for this unit. |
| What is the technical condition of this part? |
| Used, in working order and in good condition. You will find the warranty period in the product features table. |
Send any questions about the numbers or ECU preparation to contact@auto24parts.com.