A faulty transmission control module (TCM) most often causes limp mode with the gearbox stuck in one gear, harsh jolts when you select D or R, erratic gear changes, flashing PRND letters and a gearbox or engine warning light. However, the same symptoms are often caused by a low gearbox oil level, a weak battery, a poor earth or a faulty sensor. To test a transmission control module, start by checking the battery and reading the fault codes with a diagnostic tool that can talk to the gearbox control unit, then check the power supply, the connector, the oil and the live data. Below we explain the symptoms, the diagnostic steps and what the most common fault codes mean.
Engine Control Unit Volkswagen T5 Bosch ME7.5 06A906032DB 0261207677
Vendors's code: 0261207677
Product code: 0261207677
Barcode:
Code 39:
ISBN:
Select a product option:
Individual variants may differ in price
product option
Important: Depending on the ECU type and vehicle model, not all of the options listed below may be available.
To select the correct option for your vehicle and ECU, please contact us before purchasing:
contact@auto24parts.com
1. Locked
This option is intended for professional workshops with the required specialist equipment and technical knowledge.
The ECU has been removed from a vehicle intended for recycling and still contains the immobilizer data and other information from the previous vehicle. Before it can be used in another car, it must be unlocked and then programmed using specialist automotive diagnostic equipment.
2. Unlocked
Several preparation methods may be available. The possible options depend on the ECU type, vehicle model and immobilizer system. Please contact us before purchasing, as some preparation methods are not available for every ECU.
Our electronics specialists can prepare the ECU in one of the following ways:
a) ECU with PIN code (Car Pass)
The PIN code is supplied, but programming with a suitable diagnostic tool is still required. After installing the ECU, it must be reset using the supplied PIN code and then programmed to the vehicle’s immobilizer system.
b) VIRGIN ECU
The data from the previous vehicle is removed and the ECU is restored to a clean, factory-like state. After installation, it must be programmed to the vehicle using a compatible specialist diagnostic tool. Unless another preparation method is specified in the product description, this is the standard unlocking option for most of our ECUs.
c) Plug & Play – IMMO OFF
The immobilizer function is disabled in the ECU. After installation, the engine can start without additional immobilizer programming. Please note that the vehicle will no longer have an active immobilizer function, and an immobilizer warning light or fault code may remain, depending on the vehicle model.
d) Plug & Play – Automatic Programming
After installation, the ECU automatically learns and saves the required vehicle data. No additional programming is normally required.
e) Plug & Play – 1:1 Clone
The data from your original ECU is copied to another fully functional ECU. The cloned unit is then ready for installation without additional programming.
You must send us your original ECU so that we can transfer its data to the replacement unit.
The original ECU must have working communication with the vehicle, a diagnostic tool or our programming equipment. If the required data cannot be read, a complete 1:1 clone may not be possible.
3. Complete Plug & Play Set
A complete matched set containing the ECU, immobilizer components and all other parts required to start the vehicle without additional programming. All components supplied in the set must be installed in the vehicle.
Important:
Dispatch time depends on the selected option. If an unlocked or specially prepared version is ordered, the preparation service usually requires an additional 1–2 business days.
Ask about the product
Administratorem danych osobowych jest Auto24parts. Przetwarzamy je w celu przesłania odpowiedzi na zapytanie. Więcej informacji dotyczących przetwarzania danych osobowych znajduje się w polityce prywatności.
Price 30 euros applies shipments to 5 kg on worldwide. Above this weight, please contact us by email to check price
Shipping cost for the selected product
The shipping cost applies to this product (in the selected variant - if applicable). It may change after adding other products to the cart.
Looking for a Bosch ME7.5 06A906032DB ECU for a Volkswagen T5?
We offer a used Bosch ME7.5 engine control unit in working order, VW number 06A906032DB and Bosch number 0 261 207 677, removed from a petrol Volkswagen T5.
Engine Control Unit Volkswagen T5 Bosch ME7.5 06A906032DB 0261207677
The Bosch ME7.5 belongs to the Motronic family – petrol engine ECUs that combine injection, ignition and electronic throttle management. This unit comes from a Volkswagen T5 and carries VW number 06A906032DB. The data does not give the engine size, so when replacing it go by the number on the label rather than the vehicle model alone. A faulty unit can immobilise the vehicle completely or restrict it to limp mode, which in a van means lost working time.
Numbers for this unit
- 06A906032DB – Volkswagen part number
- 0261207677 – Bosch number, shown on the label as 0 261 207 677
- ME7.5 – Bosch Motronic ECU family
The final letters DB in the VW number identify the software or hardware version. ME7.5 units come in many variants, so an identical VW number matters more than the family designation alone.
Fault symptoms
- no start even though the fuel supply system is working,
- the electronic throttle does not respond and the EPC light is on,
- sudden limp mode with restricted revs,
- no communication with the ECU on the diagnostic tester.
Before replacing the unit, check the power supply, earths and connector – and make sure the throttle body itself is not the cause.
Options: locked and unlocked
If you choose an unlocked ECU, we prepare it before dispatch, usually within 1–2 working days. A locked unit holds the data and immobiliser of the previous T5 and is intended for workshops that unlock, program and match it themselves.
Whether PIN / CAR PASS, Virgin, IMMO OFF, auto programming or cloning can be used for this part number depends on the software and immobiliser. Please ask before buying. More information: ECU preparation options.
Questions and answers
| What does ME7.5 mean? |
|---|
| It is a Bosch ECU from the Motronic family, designed for petrol engines. |
| Will it fit every petrol T5? |
| No. You can only confirm the fit by the number 06A906032DB on your own unit. |
| What condition is the ECU in? |
| Used, in working order and in good condition. You will find the warranty period in the product features table. |
Not sure? Send the numbers from the label to contact@auto24parts.com.