A faulty transmission control module (TCM) most often causes limp mode with the gearbox stuck in one gear, harsh jolts when you select D or R, erratic gear changes, flashing PRND letters and a gearbox or engine warning light. However, the same symptoms are often caused by a low gearbox oil level, a weak battery, a poor earth or a faulty sensor. To test a transmission control module, start by checking the battery and reading the fault codes with a diagnostic tool that can talk to the gearbox control unit, then check the power supply, the connector, the oil and the live data. Below we explain the symptoms, the diagnostic steps and what the most common fault codes mean.
Engine Control Unit Volkswagen T5 3.2 Bosch 022906032GM 0261208752
Vendors's code: 0261208752
Product code: 0261208752
Barcode:
Code 39:
ISBN:
Select a product option:
Individual variants may differ in price
product option
Important: Depending on the ECU type and vehicle model, not all of the options listed below may be available.
To select the correct option for your vehicle and ECU, please contact us before purchasing:
contact@auto24parts.com
1. Locked
This option is intended for professional workshops with the required specialist equipment and technical knowledge.
The ECU has been removed from a vehicle intended for recycling and still contains the immobilizer data and other information from the previous vehicle. Before it can be used in another car, it must be unlocked and then programmed using specialist automotive diagnostic equipment.
2. Unlocked
Several preparation methods may be available. The possible options depend on the ECU type, vehicle model and immobilizer system. Please contact us before purchasing, as some preparation methods are not available for every ECU.
Our electronics specialists can prepare the ECU in one of the following ways:
a) ECU with PIN code (Car Pass)
The PIN code is supplied, but programming with a suitable diagnostic tool is still required. After installing the ECU, it must be reset using the supplied PIN code and then programmed to the vehicle’s immobilizer system.
b) VIRGIN ECU
The data from the previous vehicle is removed and the ECU is restored to a clean, factory-like state. After installation, it must be programmed to the vehicle using a compatible specialist diagnostic tool. Unless another preparation method is specified in the product description, this is the standard unlocking option for most of our ECUs.
c) Plug & Play – IMMO OFF
The immobilizer function is disabled in the ECU. After installation, the engine can start without additional immobilizer programming. Please note that the vehicle will no longer have an active immobilizer function, and an immobilizer warning light or fault code may remain, depending on the vehicle model.
d) Plug & Play – Automatic Programming
After installation, the ECU automatically learns and saves the required vehicle data. No additional programming is normally required.
e) Plug & Play – 1:1 Clone
The data from your original ECU is copied to another fully functional ECU. The cloned unit is then ready for installation without additional programming.
You must send us your original ECU so that we can transfer its data to the replacement unit.
The original ECU must have working communication with the vehicle, a diagnostic tool or our programming equipment. If the required data cannot be read, a complete 1:1 clone may not be possible.
3. Complete Plug & Play Set
A complete matched set containing the ECU, immobilizer components and all other parts required to start the vehicle without additional programming. All components supplied in the set must be installed in the vehicle.
Important:
Dispatch time depends on the selected option. If an unlocked or specially prepared version is ordered, the preparation service usually requires an additional 1–2 business days.
Ask about the product
Administratorem danych osobowych jest Auto24parts. Przetwarzamy je w celu przesłania odpowiedzi na zapytanie. Więcej informacji dotyczących przetwarzania danych osobowych znajduje się w polityce prywatności.
Price 30 euros applies shipments to 5 kg on worldwide. Above this weight, please contact us by email to check price
Shipping cost for the selected product
The shipping cost applies to this product (in the selected variant - if applicable). It may change after adding other products to the cart.
How does the 022906032GM ECU differ from other modules for the T5 3.2?
By version – the GM ending and the Bosch number 0 261 208 752 distinguish it from, for example, the 022906032JB module. We offer a used, working ECU for the Volkswagen T5 with the 3.2 petrol engine.
Engine Control Unit Volkswagen T5 3.2 Bosch 022906032GM 0261208752
Several versions of the engine ECU with a number starting 022906032 were used in the Volkswagen T5 with the 3.2 petrol engine. This unit is the GM version, made by Bosch, with number 0261208752. The module manages fuel injection, ignition and the throttle, and also stores faults that you can read with a tester. The number 022906032GM is the main reference point when replacing it – the engine size and car model alone are not enough to choose the right module. When the ECU stops working, the T5 usually cannot be started or runs in limp mode.
Numbers to verify
- 022906032GM – VW part number
- 0261208752 – Bosch number, 0 261 208 752 on the sticker
The letters at the end of the VW number – here GM – indicate the software or hardware version. A 022906032 ECU with a different ending may need different settings, so choose it by the full number, not just by engine size.
Symptoms pointing to the ECU
- no start despite working ignition and fuel pump,
- limp mode and limited revs,
- the engine cutting out by itself with no sensor fault,
- no communication with the module in diagnostics.
Before ordering an ECU, check the earths, power supply and condition of the connector – moisture in the wiring loom produces similar symptoms.
Which version should I order?
We will prepare an unlocked module before dispatch; this usually takes 1–2 working days. A locked one keeps the data and immobiliser of the previous T5 – it is intended for workshops that will take care of the unlocking, programming and adaptation themselves.
The availability of PIN / CAR PASS, a Virgin version, IMMO OFF, auto programming or a clone depends on the number, software and immobiliser. Please ask before buying. Details: ECU preparation options page.
Questions and answers
| Will the 022906032GM replace the 022906032JB? |
|---|
| Do not assume so – they are different versions. Send us your module's number and we will check. |
| Will the T5 start after fitting the locked version? |
| No, it needs programming and adaptation to the immobiliser. |
| What condition is the ECU in? |
| Used, working and in good condition. You will find the warranty period in the product features table. |
Want to compare numbers? Email contact@auto24parts.com.