A properly functioning ABS system is the foundation of road safety. Its main task is to prevent wheel lock-up during emergency braking, which allows the driver to maintain full control of the vehicle. The heart of this system is the electronic ABS pump controller. When it fails, the system stops working. A proper diagnosis of the problem allows you to avoid unnecessary costs and quickly restore brake efficiency.
EGR Control Unit Rexton 2.9TD 2880005050
Vendors's code:
Product code: 5F62-98481
Barcode:
Code 39:
ISBN:
€203.25
Price
€203.25
Regular price:
€203.25
0%
€250.00
Price
€250.00
Regular price:
€250.00
0%
Select a product option:
Individual variants may differ in price
product option
Important: Depending on the ECU type and vehicle model, not all of the options listed below may be available.
To select the correct option for your vehicle and ECU, please contact us before purchasing:
contact@auto24parts.com
1. Locked
This option is intended for professional workshops with the required specialist equipment and technical knowledge.
The ECU has been removed from a vehicle intended for recycling and still contains the immobilizer data and other information from the previous vehicle. Before it can be used in another car, it must be unlocked and then programmed using specialist automotive diagnostic equipment.
2. Unlocked
Several preparation methods may be available. The possible options depend on the ECU type, vehicle model and immobilizer system. Please contact us before purchasing, as some preparation methods are not available for every ECU.
Our electronics specialists can prepare the ECU in one of the following ways:
a) ECU with PIN code (Car Pass)
The PIN code is supplied, but programming with a suitable diagnostic tool is still required. After installing the ECU, it must be reset using the supplied PIN code and then programmed to the vehicle’s immobilizer system.
b) VIRGIN ECU
The data from the previous vehicle is removed and the ECU is restored to a clean, factory-like state. After installation, it must be programmed to the vehicle using a compatible specialist diagnostic tool. Unless another preparation method is specified in the product description, this is the standard unlocking option for most of our ECUs.
c) Plug & Play – IMMO OFF
The immobilizer function is disabled in the ECU. After installation, the engine can start without additional immobilizer programming. Please note that the vehicle will no longer have an active immobilizer function, and an immobilizer warning light or fault code may remain, depending on the vehicle model.
d) Plug & Play – Automatic Programming
After installation, the ECU automatically learns and saves the required vehicle data. No additional programming is normally required.
e) Plug & Play – 1:1 Clone
The data from your original ECU is copied to another fully functional ECU. The cloned unit is then ready for installation without additional programming.
You must send us your original ECU so that we can transfer its data to the replacement unit.
The original ECU must have working communication with the vehicle, a diagnostic tool or our programming equipment. If the required data cannot be read, a complete 1:1 clone may not be possible.
3. Complete Plug & Play Set
A complete matched set containing the ECU, immobilizer components and all other parts required to start the vehicle without additional programming. All components supplied in the set must be installed in the vehicle.
Important:
Dispatch time depends on the selected option. If an unlocked or specially prepared version is ordered, the preparation service usually requires an additional 1–2 business days.
Ask about the product
EGR Control Unit Rexton 2.9TD 2880005050
Administratorem danych osobowych jest Auto24parts. Przetwarzamy je w celu przesłania odpowiedzi na zapytanie. Więcej informacji dotyczących przetwarzania danych osobowych znajduje się w polityce prywatności.
Shipping
from
€30.00
-
shipping
(Poland)
from
€30.00
-
shipping
(Poland)
Price 30 euros applies shipments to 5 kg on worldwide. Above this weight, please contact us by email to check price
Shipping cost for the selected product
The shipping cost applies to this product (in the selected variant - if applicable). It may change after adding other products to the cart.
EGR control unit Rexton 2.9TD 2880005050
The EGR control unit for Rexton 2.9TD with part number 2880005050 is a well-matched solution when replacing a damaged module – before purchasing, check the part number to ensure proper compatibility with your vehicle.
What does the number 2880005050 mean on the EGR control unit for Rexton 2.9TD?
The number 2880005050 identifies a specific EGR control unit used in the Rexton 2.9TD model. This designation allows precise matching of the part to the correct engine version.
Will the EGR control unit 28800-05050 fit my Rexton 2.9TD?
To confirm compatibility, compare the number 28800-05050 with the marking on the original module installed in your vehicle. Full number matching is essential when selecting the correct part.
What function does the EGR computer 2880005050 perform?
The EGR control unit with number 2880005050 manages the proper operation of the exhaust gas recirculation valve. Thanks to it, the Rexton 2.9TD engine runs smoothly and maintains correct operating parameters.
What symptoms may indicate a faulty 2880005050 control unit?
Loss of power, uneven engine operation or an illuminated engine warning light may indicate a problem with the 2880005050 module. Replacing it with a working unit often restores proper vehicle performance.
Why is the exact number 2880005050 important when purchasing?
EGR modules may look similar, but the number 2880005050 determines compatibility with the 2.9TD engine. Even a small difference in the code may indicate a different variant.
Does the EGR unit 28800-05050 require programming after installation?
Depending on the vehicle version, the 28800-05050 control unit may require adaptation after installation. It is advisable to verify this before fitting.
How can I check compatibility of the 2880005050 module with my Rexton?
The best method is to compare the number 2880005050 with the marking on your old part. Matching numbers minimize the risk of incorrect fitment.
Why search for the control unit by number 2880005050?
Entering the exact number 2880005050 in a search engine helps you quickly find the correct EGR control unit for Rexton 2.9TD. It is the most accurate way to select the right part.
What should I check before ordering the EGR control unit 2880005050?
Before purchasing, make sure that the number 2880005050 or 28800-05050 fully matches the marking on your original part. Verifying compatibility helps avoid unnecessary returns.
Is the EGR control unit 2880005050 available in different versions?
Depending on the production year and engine version of the Rexton 2.9TD, the 2880005050 module may be available in different variants. It is recommended to carefully review the product description before choosing.
