The automatic transmission control unit (often designated as TCU or TCM) is a crucial electronic component responsible for smooth and trouble-free gear shifting. Its failure, most often caused by overheating, short circuits, or water damage, results in jerking, an inability to shift gears, or the vehicle entering limp mode. Purchasing a new module at an authorized dealership is a massive expense, which is why replacing it with a fully functional, used original is the most reasonable solution.
ECU Engine Controller Alfa Romeo 159 1.9 JTD 0281012144 55205068 9394234A3BBM150
Vendors's code: 55205068
Product code: BD7D-4461C
Barcode:
Code 39:
ISBN:
€243.90
Price
€243.90
€300.00
Price
€300.00
In stock
Select a product option:
Individual variants may differ in price
product option
Important: Depending on the ECU type and vehicle model, not all of the options listed below may be available.
To select the correct option for your vehicle and ECU, please contact us before purchasing:
contact@auto24parts.com
1. Locked
This option is intended for professional workshops with the required specialist equipment and technical knowledge.
The ECU has been removed from a vehicle intended for recycling and still contains the immobilizer data and other information from the previous vehicle. Before it can be used in another car, it must be unlocked and then programmed using specialist automotive diagnostic equipment.
2. Unlocked
Several preparation methods may be available. The possible options depend on the ECU type, vehicle model and immobilizer system. Please contact us before purchasing, as some preparation methods are not available for every ECU.
Our electronics specialists can prepare the ECU in one of the following ways:
a) ECU with PIN code (Car Pass)
The PIN code is supplied, but programming with a suitable diagnostic tool is still required. After installing the ECU, it must be reset using the supplied PIN code and then programmed to the vehicle’s immobilizer system.
b) VIRGIN ECU
The data from the previous vehicle is removed and the ECU is restored to a clean, factory-like state. After installation, it must be programmed to the vehicle using a compatible specialist diagnostic tool. Unless another preparation method is specified in the product description, this is the standard unlocking option for most of our ECUs.
c) Plug & Play – IMMO OFF
The immobilizer function is disabled in the ECU. After installation, the engine can start without additional immobilizer programming. Please note that the vehicle will no longer have an active immobilizer function, and an immobilizer warning light or fault code may remain, depending on the vehicle model.
d) Plug & Play – Automatic Programming
After installation, the ECU automatically learns and saves the required vehicle data. No additional programming is normally required.
e) Plug & Play – 1:1 Clone
The data from your original ECU is copied to another fully functional ECU. The cloned unit is then ready for installation without additional programming.
You must send us your original ECU so that we can transfer its data to the replacement unit.
The original ECU must have working communication with the vehicle, a diagnostic tool or our programming equipment. If the required data cannot be read, a complete 1:1 clone may not be possible.
3. Complete Plug & Play Set
A complete matched set containing the ECU, immobilizer components and all other parts required to start the vehicle without additional programming. All components supplied in the set must be installed in the vehicle.
Important:
Dispatch time depends on the selected option. If an unlocked or specially prepared version is ordered, the preparation service usually requires an additional 1–2 business days.
Ask about the product
ECU Engine Controller Alfa Romeo 159 1.9 JTD 0281012144 55205068 9394234A3BBM150
Administratorem danych osobowych jest Auto24parts. Przetwarzamy je w celu przesłania odpowiedzi na zapytanie. Więcej informacji dotyczących przetwarzania danych osobowych znajduje się w polityce prywatności.
Shipping
from
€30.00
-
shipping
(Poland)
from
€30.00
-
shipping
(Poland)
Price 30 euros applies shipments to 5 kg on worldwide. Above this weight, please contact us by email to check price
Shipping cost for the selected product
The shipping cost applies to this product (in the selected variant - if applicable). It may change after adding other products to the cart.
Engine control unit Alfa Romeo 159 1.9 JTD 0281012144 55205068 9394234A3BBM150
The engine control unit for Alfa Romeo 159 1.9 JTD with part numbers 0281012144, 55205068 and 9394234A3BBM150 is a proven solution when replacing a damaged module – before purchasing, please read the variant description, as the engine controller is available in a locked or unlocked version.
FAQ – ECU Engine Controller Alfa Romeo 159 1.9 JTD 0281012144 / 55205068 / 9394234A3BBM150
Is the engine control unit 0281012144 compatible with Alfa Romeo 159 1.9 JTD?
Yes, if your current unit has the number 0281012144, this model will be compatible with Alfa Romeo 159 1.9 JTD. Matching the part number ensures proper fitment and hassle-free installation.
What does the number 55205068 mean on an Alfa Romeo 159 ECU?
The number 55205068 is a manufacturer reference for the same engine control unit. It may appear alongside the Bosch number but refers to the same module used in the Alfa Romeo 159.
Can the ECU 9394234A3BBM150 be installed without issues?
Yes, if the number 9394234A3BBM150 matches your original unit, installation is straightforward and requires no modifications. It is a plug & play solution when numbers match.
How can I check if ECU 0281012144 or 55205068 fits my car?
The best way is to compare the part number directly with your current ECU or verify compatibility using your VIN. Matching numbers guarantee proper operation.
Does the Alfa Romeo 159 1.9 JTD ECU require coding after installation?
In most cases, no additional coding is required if the unit is properly prepared. After installation, the car should start and run normally like with the original ECU.
