A properly functioning ABS system is the foundation of road safety. Its main task is to prevent wheel lock-up during emergency braking, which allows the driver to maintain full control of the vehicle. The heart of this system is the electronic ABS pump controller. When it fails, the system stops working. A proper diagnosis of the problem allows you to avoid unnecessary costs and quickly restore brake efficiency.
Engine control module Audi 0281018748 03L906018KM EDC17C46
Vendors's code:
Product code: F8D4-5335E
Barcode:
Code 39:
ISBN:
1 300,81 zł
Price
1 300,81 zł
Regular price:
1 300,81 zł
0%
1 600,00 zł
Price
1 600,00 zł
Regular price:
1 600,00 zł
0%
In stock
Select a product option:
Individual variants may differ in price
product option
Important: Depending on the ECU type and vehicle model, not all of the options listed below may be available.
To select the correct option for your vehicle and ECU, please contact us before purchasing:
contact@auto24parts.com
1. Locked
This option is intended for professional workshops with the required specialist equipment and technical knowledge.
The ECU has been removed from a vehicle intended for recycling and still contains the immobilizer data and other information from the previous vehicle. Before it can be used in another car, it must be unlocked and then programmed using specialist automotive diagnostic equipment.
2. Unlocked
Several preparation methods may be available. The possible options depend on the ECU type, vehicle model and immobilizer system. Please contact us before purchasing, as some preparation methods are not available for every ECU.
Our electronics specialists can prepare the ECU in one of the following ways:
a) ECU with PIN code (Car Pass)
The PIN code is supplied, but programming with a suitable diagnostic tool is still required. After installing the ECU, it must be reset using the supplied PIN code and then programmed to the vehicle’s immobilizer system.
b) VIRGIN ECU
The data from the previous vehicle is removed and the ECU is restored to a clean, factory-like state. After installation, it must be programmed to the vehicle using a compatible specialist diagnostic tool. Unless another preparation method is specified in the product description, this is the standard unlocking option for most of our ECUs.
c) Plug & Play – IMMO OFF
The immobilizer function is disabled in the ECU. After installation, the engine can start without additional immobilizer programming. Please note that the vehicle will no longer have an active immobilizer function, and an immobilizer warning light or fault code may remain, depending on the vehicle model.
d) Plug & Play – Automatic Programming
After installation, the ECU automatically learns and saves the required vehicle data. No additional programming is normally required.
e) Plug & Play – 1:1 Clone
The data from your original ECU is copied to another fully functional ECU. The cloned unit is then ready for installation without additional programming.
You must send us your original ECU so that we can transfer its data to the replacement unit.
The original ECU must have working communication with the vehicle, a diagnostic tool or our programming equipment. If the required data cannot be read, a complete 1:1 clone may not be possible.
3. Complete Plug & Play Set
A complete matched set containing the ECU, immobilizer components and all other parts required to start the vehicle without additional programming. All components supplied in the set must be installed in the vehicle.
Important:
Dispatch time depends on the selected option. If an unlocked or specially prepared version is ordered, the preparation service usually requires an additional 1–2 business days.
Ask about the product
Engine control module Audi 0281018748 03L906018KM EDC17C46
Administratorem danych osobowych jest Auto24parts. Przetwarzamy je w celu przesłania odpowiedzi na zapytanie. Więcej informacji dotyczących przetwarzania danych osobowych znajduje się w polityce prywatności.
Shipping
from
120,00 zł
-
shipping
(Poland)
from
120,00 zł
-
shipping
(Poland)
Price 30 euros applies shipments to 5 kg on worldwide. Above this weight, please contact us by email to check price
Shipping cost for the selected product
The shipping cost applies to this product (in the selected variant - if applicable). It may change after adding other products to the cart.
Engine control unit Audi 0281018748 03L906018KM EDC17C46
The engine control unit with numbers 0281018748 and 03L906018KM EDC17C46 for Audi is a tested part responsible for engine operation, available in a locked or unlocked version.
Does engine control unit 0281018748 fit Audi?
The engine control unit 0281018748 with designation 03L906018KM EDC17C46 is an original Bosch ECU used in Audi A4 B8 and Audi A4 Allroad 2.0 TDI. It manages fuel injection, turbocharging and emissions control.
What does 03L906018KM mean?
03L906018KM is the Audi/VW part number identifying the exact ECU version together with Bosch 0281018748.
According to catalog data, this ECU is used in Audi A4 Allroad 2.0 TDI (B8) 130 kW versions.
What does EDC17C46 mean?
EDC17C46 is a Bosch diesel ECU family responsible for injection, rail pressure, turbo control and emissions.
Which cars use 0281018748?
- Audi A4 B8 2.0 TDI
- Audi A4 Allroad 2.0 TDI
- selected VAG EA189 2.0 TDI models
Does 0281018748 require programming?
Yes — it may be locked, virgin or plug & play depending on version.
How to check compatibility?
Compare 0281018748 or 03L906018KM with your current ECU.
Why is 0281018748 important?
It uniquely identifies this EDC17C46 ECU version.
Is 03L906018KM plug & play?
It depends on the unit version and may require immobilizer adaptation.
Symptoms of faulty ECU
No start, limp mode, no communication or injection/turbo faults.
What to check before buying?
Match numbers, check condition and choose correct version.
