A faulty transmission control module (TCM) most often causes limp mode with the gearbox stuck in one gear, harsh jolts when you select D or R, erratic gear changes, flashing PRND letters and a gearbox or engine warning light. However, the same symptoms are often caused by a low gearbox oil level, a weak battery, a poor earth or a faulty sensor. To test a transmission control module, start by checking the battery and reading the fault codes with a diagnostic tool that can talk to the gearbox control unit, then check the power supply, the connector, the oil and the live data. Below we explain the symptoms, the diagnostic steps and what the most common fault codes mean.
Engine control unit Kia Carens 2.0 CRDI 0281012671 3911327370
Vendors's code: 0281012671
Product code: 52E9-71450
Barcode:
Code 39:
ISBN:
£154.39
Price
£154.39
£189.90
Price
£189.90
In stock
Select a product option:
Individual variants may differ in price
product option
Important: Depending on the ECU type and vehicle model, not all of the options listed below may be available.
To select the correct option for your vehicle and ECU, please contact us before purchasing:
contact@auto24parts.com
1. Locked
This option is intended for professional workshops with the required specialist equipment and technical knowledge.
The ECU has been removed from a vehicle intended for recycling and still contains the immobilizer data and other information from the previous vehicle. Before it can be used in another car, it must be unlocked and then programmed using specialist automotive diagnostic equipment.
2. Unlocked
Several preparation methods may be available. The possible options depend on the ECU type, vehicle model and immobilizer system. Please contact us before purchasing, as some preparation methods are not available for every ECU.
Our electronics specialists can prepare the ECU in one of the following ways:
a) ECU with PIN code (Car Pass)
The PIN code is supplied, but programming with a suitable diagnostic tool is still required. After installing the ECU, it must be reset using the supplied PIN code and then programmed to the vehicle’s immobilizer system.
b) VIRGIN ECU
The data from the previous vehicle is removed and the ECU is restored to a clean, factory-like state. After installation, it must be programmed to the vehicle using a compatible specialist diagnostic tool. Unless another preparation method is specified in the product description, this is the standard unlocking option for most of our ECUs.
c) Plug & Play – IMMO OFF
The immobilizer function is disabled in the ECU. After installation, the engine can start without additional immobilizer programming. Please note that the vehicle will no longer have an active immobilizer function, and an immobilizer warning light or fault code may remain, depending on the vehicle model.
d) Plug & Play – Automatic Programming
After installation, the ECU automatically learns and saves the required vehicle data. No additional programming is normally required.
e) Plug & Play – 1:1 Clone
The data from your original ECU is copied to another fully functional ECU. The cloned unit is then ready for installation without additional programming.
You must send us your original ECU so that we can transfer its data to the replacement unit.
The original ECU must have working communication with the vehicle, a diagnostic tool or our programming equipment. If the required data cannot be read, a complete 1:1 clone may not be possible.
3. Complete Plug & Play Set
A complete matched set containing the ECU, immobilizer components and all other parts required to start the vehicle without additional programming. All components supplied in the set must be installed in the vehicle.
Important:
Dispatch time depends on the selected option. If an unlocked or specially prepared version is ordered, the preparation service usually requires an additional 1–2 business days.
Ask about the product
Engine control unit Kia Carens 2.0 CRDI 0281012671 3911327370
Administratorem danych osobowych jest Auto24parts. Przetwarzamy je w celu przesłania odpowiedzi na zapytanie. Więcej informacji dotyczących przetwarzania danych osobowych znajduje się w polityce prywatności.
Shipping
from
£22.79
-
shipping
(Poland)
from
£22.79
-
shipping
(Poland)
Price 30 euros applies shipments to 5 kg on worldwide. Above this weight, please contact us by email to check price
Shipping cost for the selected product
The shipping cost applies to this product (in the selected variant - if applicable). It may change after adding other products to the cart.
Is this Kia Carens control unit the right one for your engine?
A used engine control unit in working order and in good condition for the Kia Carens - numbers 0 281 012 671 / 0281012671; 39113-27370 / 3911327370. The numbers are listed below, and if you have any questions about the fit, write to us.
Engine control unit for Kia Carens
If your Kia Carens 2.0 CRDI is hard to start, loses power or has the engine warning light on, the control unit may be the cause. We are selling a used module in working order and in good condition.
Numbers to compare
- 0 281 012 671 / 0281012671 - manufacturer's number (Bosch)
- 39113-27370 / 3911327370 - part number (OEM / vehicle)
Application according to the listing
- Kia Carens - model
- 2.0 CRDI - engine according to the listing
- Bosch - manufacturer
What an engine control unit does
The control unit communicates with the car's other modules over the CAN bus, including the ABS, the gearbox and the instrument cluster. That is why the software version and the hardware number matter when matching. After replacement, the module usually has to be matched to the car, and in some cars it also needs coding or adaptation.
Fitment
Compare number 0 281 012 671 in full with the number on your control unit. Different versions were fitted to the same models, so it is the number that decides the match, not the model alone. The same engine type was sometimes controlled by different module versions, so the number decides the match first, and only then the model and year.
Symptoms of a faulty control unit
- no power to the injectors,
- memory and checksum errors,
- the engine will not start despite a healthy battery,
- the control unit reports an internal fault.
Note down the stored fault codes before removing the unit, as after the replacement they will help you judge whether the problem has been solved.
Locked or unlocked variant?
A locked control unit is sold with the previous vehicle's data - this is an option for workshops that can unlock and program it. We prepare an unlocked control unit before dispatch, which usually takes about 1-2 working days. Not every unlocking method (PIN / CAR PASS, Virgin, IMMO OFF, auto-programming, cloning) is available for every control unit - it depends on the number, software and immobiliser. See our ECU preparation options and contact us before buying.
Questions and answers
| Is the part new? |
|---|
| The control unit is used, but in working order. The warranty is stated in the product features. |
| Why is the number written in several ways? |
| The same number may be written with spaces, with hyphens or as a single string. We give it in two forms to make it easier to find. |
| What is the difference between the locked and the unlocked variant? |
| A locked unit holds the previous car's data and immobiliser coding, while an unlocked one is prepared by us before dispatch. You will find a description on our ECU preparation options page. |
Not sure? Write to contact@auto24parts.com and we will help you choose the right control unit for your car.
