A properly functioning ABS system is the foundation of road safety. Its main task is to prevent wheel lock-up during emergency braking, which allows the driver to maintain full control of the vehicle. The heart of this system is the electronic ABS pump controller. When it fails, the system stops working. A proper diagnosis of the problem allows you to avoid unnecessary costs and quickly restore brake efficiency.
ECU Engine controller AUDI A3 2.0 TDI 03G906016FF BOSCH 0281011905
Vendors's code: 03G906016FF
Product code: C074-91557
Barcode:
Code 39:
ISBN:
€81.30
Price
€81.30
Regular price:
€81.30
0%
€100.00
Price
€100.00
Regular price:
€100.00
0%
Select a product option:
Individual variants may differ in price
product option
Important: Depending on the ECU type and vehicle model, not all of the options listed below may be available.
To select the correct option for your vehicle and ECU, please contact us before purchasing:
contact@auto24parts.com
1. Locked
This option is intended for professional workshops with the required specialist equipment and technical knowledge.
The ECU has been removed from a vehicle intended for recycling and still contains the immobilizer data and other information from the previous vehicle. Before it can be used in another car, it must be unlocked and then programmed using specialist automotive diagnostic equipment.
2. Unlocked
Several preparation methods may be available. The possible options depend on the ECU type, vehicle model and immobilizer system. Please contact us before purchasing, as some preparation methods are not available for every ECU.
Our electronics specialists can prepare the ECU in one of the following ways:
a) ECU with PIN code (Car Pass)
The PIN code is supplied, but programming with a suitable diagnostic tool is still required. After installing the ECU, it must be reset using the supplied PIN code and then programmed to the vehicle’s immobilizer system.
b) VIRGIN ECU
The data from the previous vehicle is removed and the ECU is restored to a clean, factory-like state. After installation, it must be programmed to the vehicle using a compatible specialist diagnostic tool. Unless another preparation method is specified in the product description, this is the standard unlocking option for most of our ECUs.
c) Plug & Play – IMMO OFF
The immobilizer function is disabled in the ECU. After installation, the engine can start without additional immobilizer programming. Please note that the vehicle will no longer have an active immobilizer function, and an immobilizer warning light or fault code may remain, depending on the vehicle model.
d) Plug & Play – Automatic Programming
After installation, the ECU automatically learns and saves the required vehicle data. No additional programming is normally required.
e) Plug & Play – 1:1 Clone
The data from your original ECU is copied to another fully functional ECU. The cloned unit is then ready for installation without additional programming.
You must send us your original ECU so that we can transfer its data to the replacement unit.
The original ECU must have working communication with the vehicle, a diagnostic tool or our programming equipment. If the required data cannot be read, a complete 1:1 clone may not be possible.
3. Complete Plug & Play Set
A complete matched set containing the ECU, immobilizer components and all other parts required to start the vehicle without additional programming. All components supplied in the set must be installed in the vehicle.
Important:
Dispatch time depends on the selected option. If an unlocked or specially prepared version is ordered, the preparation service usually requires an additional 1–2 business days.
Ask about the product
ECU Engine controller AUDI A3 2.0 TDI 03G906016FF BOSCH 0281011905
Administratorem danych osobowych jest Auto24parts. Przetwarzamy je w celu przesłania odpowiedzi na zapytanie. Więcej informacji dotyczących przetwarzania danych osobowych znajduje się w polityce prywatności.
Shipping
from
€30.00
-
shipping
(Poland)
from
€30.00
-
shipping
(Poland)
Price 30 euros applies shipments to 5 kg on worldwide. Above this weight, please contact us by email to check price
Shipping cost for the selected product
The shipping cost applies to this product (in the selected variant - if applicable). It may change after adding other products to the cart.
ECU Engine controller 03G906016FF BOSCH 0281011905 for AUDI A3 2.0 TDI
Original ECU Engine controller with numbers 03G906016FF and 0281011905 for Audi A3 2.0 TDI – guaranteed fit and stable operation after installation.
Is the 03G906016FF Engine controller compatible with Audi A3 2.0 TDI?
Yes, the Engine controller with part number 03G906016FF is used in Audi A3 with a 2.0 TDI engine. If your unit also shows the Bosch number 0281011905, it means it is exactly the same unit and should fit without any issues.
How to check if the 0281011905 Engine controller is suitable for Audi A3 8P 2.0 TDI?
The most important step is to compare part numbers – 0281011905 and 03G906016FF. In Audi A3 8P 2.0 TDI, these markings often appear together, so matching numbers provide strong assurance that the controller will function correctly.
Is the BOSCH 0281011905 Engine controller compatible with VW Golf 5 2.0 TDI?
Yes, the Bosch 0281011905 Engine controller with OEM number 03G906016FF was also used in other VAG group models such as VW Golf 5 2.0 TDI. It is a widely used Engine controller in diesel engines of this displacement.
What is the difference between 03G906016FF and other versions in Audi A3 2.0 TDI?
Differences between controllers such as 03G906016FF and other versions or Bosch references like 0281011905 may relate to engine maps, software versions, or immobilizer configuration. Therefore, it is always best to choose an identical part number.
Does the 03G906016FF Bosch 0281011905 Engine controller require programming in Audi A3?
In most cases, yes – the 03G906016FF / 0281011905 Engine controller requires adaptation, immobilizer coding, or preparation such as immo off after installation in Audi A3 2.0 TDI. This is a standard procedure when replacing an ECU.
