A faulty transmission control module (TCM) most often causes limp mode with the gearbox stuck in one gear, harsh jolts when you select D or R, erratic gear changes, flashing PRND letters and a gearbox or engine warning light. However, the same symptoms are often caused by a low gearbox oil level, a weak battery, a poor earth or a faulty sensor. To test a transmission control module, start by checking the battery and reading the fault codes with a diagnostic tool that can talk to the gearbox control unit, then check the power supply, the connector, the oil and the live data. Below we explain the symptoms, the diagnostic steps and what the most common fault codes mean.
Engine Control Unit Volkswagen Skoda 1.9 TDI Bosch EDC16U34 03G906021AN 0281012085
Vendors's code: 0281012085
Product code: 0281012085
Barcode:
Code 39:
ISBN:
Select a product option:
Individual variants may differ in price
product option
Important: Depending on the ECU type and vehicle model, not all of the options listed below may be available.
To select the correct option for your vehicle and ECU, please contact us before purchasing:
contact@auto24parts.com
1. Locked
This option is intended for professional workshops with the required specialist equipment and technical knowledge.
The ECU has been removed from a vehicle intended for recycling and still contains the immobilizer data and other information from the previous vehicle. Before it can be used in another car, it must be unlocked and then programmed using specialist automotive diagnostic equipment.
2. Unlocked
Several preparation methods may be available. The possible options depend on the ECU type, vehicle model and immobilizer system. Please contact us before purchasing, as some preparation methods are not available for every ECU.
Our electronics specialists can prepare the ECU in one of the following ways:
a) ECU with PIN code (Car Pass)
The PIN code is supplied, but programming with a suitable diagnostic tool is still required. After installing the ECU, it must be reset using the supplied PIN code and then programmed to the vehicle’s immobilizer system.
b) VIRGIN ECU
The data from the previous vehicle is removed and the ECU is restored to a clean, factory-like state. After installation, it must be programmed to the vehicle using a compatible specialist diagnostic tool. Unless another preparation method is specified in the product description, this is the standard unlocking option for most of our ECUs.
c) Plug & Play – IMMO OFF
The immobilizer function is disabled in the ECU. After installation, the engine can start without additional immobilizer programming. Please note that the vehicle will no longer have an active immobilizer function, and an immobilizer warning light or fault code may remain, depending on the vehicle model.
d) Plug & Play – Automatic Programming
After installation, the ECU automatically learns and saves the required vehicle data. No additional programming is normally required.
e) Plug & Play – 1:1 Clone
The data from your original ECU is copied to another fully functional ECU. The cloned unit is then ready for installation without additional programming.
You must send us your original ECU so that we can transfer its data to the replacement unit.
The original ECU must have working communication with the vehicle, a diagnostic tool or our programming equipment. If the required data cannot be read, a complete 1:1 clone may not be possible.
3. Complete Plug & Play Set
A complete matched set containing the ECU, immobilizer components and all other parts required to start the vehicle without additional programming. All components supplied in the set must be installed in the vehicle.
Important:
Dispatch time depends on the selected option. If an unlocked or specially prepared version is ordered, the preparation service usually requires an additional 1–2 business days.
Ask about the product
Administratorem danych osobowych jest Auto24parts. Przetwarzamy je w celu przesłania odpowiedzi na zapytanie. Więcej informacji dotyczących przetwarzania danych osobowych znajduje się w polityce prywatności.
Price 30 euros applies shipments to 5 kg on worldwide. Above this weight, please contact us by email to check price
Shipping cost for the selected product
The shipping cost applies to this product (in the selected variant - if applicable). It may change after adding other products to the cart.
What does number 03G906021AN on the 1.9 TDI ECU mean?
03G906021AN is the Volkswagen number of a Bosch EDC16U34 engine ECU, and 0281012085 (0 281 012 085) is the number assigned by Bosch. This used, working module comes from a 2005 Volkswagen or Skoda 1.9 TDI.
Engine Control Unit Volkswagen, Skoda 1.9 TDI Bosch EDC16U34 03G906021AN 0281012085
EDC16U34 is the Bosch Electronic Diesel Control ECU family that includes module 03G906021AN. This unit was removed from a 2005 Volkswagen or Skoda 1.9 TDI. The ECU calculates the fuel quantity and injection timing, regulates turbo boost and works with the immobiliser.
Numbers on the label
- 03G906021AN – Volkswagen part number
- 0281012085 – Bosch number, shown on the sticker as 0 281 012 085
- EDC16U34 – Bosch ECU family
EDC16U34 ECUs for the 1.9 TDI come in many 03G906021 versions with different letters. AN at the end is a specific software and hardware version, so look for exactly this suffix.
Symptoms of module failure
- no start with a working fuel system,
- the tester cannot establish communication with the module,
- the engine in limp mode with reduced power,
- ECU faults after water ingress or a voltage spike.
Before replacing the ECU, check the power supply, earths and connector pins. It is also worth reading the stored fault codes – they will help distinguish a module fault from a sensor failure.
Locked and unlocked options
ECU 03G906021AN is available in an unlocked version, which we prepare before dispatch (usually 1–2 working days), and a locked version – with the data and immobiliser of the previous vehicle, for workshops that will unlock, program and match the module themselves.
Whether PIN / CAR PASS, Virgin, IMMO OFF, auto programming or cloning will be possible depends on the number, software and immobiliser – not every method works with every ECU. Please ask us before buying. Description: ECU preparation options.
Questions and answers
| Does the ECU fit a Skoda 1.9 TDI from a different year? |
|---|
| The year is helpful, but number 03G906021AN on your module is what decides. |
| What does EDC16U34 mean? |
| It is the designation of the Bosch ECU family for diesel engines. |
| What condition is the ECU in? |
| Used, in working order and in good condition. You will find the warranty period in the product features table. |
Email contact@auto24parts.com – we will help you choose the right option.