A properly functioning ABS system is the foundation of road safety. Its main task is to prevent wheel lock-up during emergency braking, which allows the driver to maintain full control of the vehicle. The heart of this system is the electronic ABS pump controller. When it fails, the system stops working. A proper diagnosis of the problem allows you to avoid unnecessary costs and quickly restore brake efficiency.
ECU Engine controller CITROEN PEUGEOT 3.0 S101700101K
Vendors's code:
Product code: 2BC7-43211
Barcode:
Code 39:
ISBN:
€142.28
Price
€142.28
€175.00
Price
€175.00
Select a product option:
Individual variants may differ in price
product option
Important: Depending on the ECU type and vehicle model, not all of the options listed below may be available.
To select the correct option for your vehicle and ECU, please contact us before purchasing:
contact@auto24parts.com
1. Locked
This option is intended for professional workshops with the required specialist equipment and technical knowledge.
The ECU has been removed from a vehicle intended for recycling and still contains the immobilizer data and other information from the previous vehicle. Before it can be used in another car, it must be unlocked and then programmed using specialist automotive diagnostic equipment.
2. Unlocked
Several preparation methods may be available. The possible options depend on the ECU type, vehicle model and immobilizer system. Please contact us before purchasing, as some preparation methods are not available for every ECU.
Our electronics specialists can prepare the ECU in one of the following ways:
a) ECU with PIN code (Car Pass)
The PIN code is supplied, but programming with a suitable diagnostic tool is still required. After installing the ECU, it must be reset using the supplied PIN code and then programmed to the vehicle’s immobilizer system.
b) VIRGIN ECU
The data from the previous vehicle is removed and the ECU is restored to a clean, factory-like state. After installation, it must be programmed to the vehicle using a compatible specialist diagnostic tool. Unless another preparation method is specified in the product description, this is the standard unlocking option for most of our ECUs.
c) Plug & Play – IMMO OFF
The immobilizer function is disabled in the ECU. After installation, the engine can start without additional immobilizer programming. Please note that the vehicle will no longer have an active immobilizer function, and an immobilizer warning light or fault code may remain, depending on the vehicle model.
d) Plug & Play – Automatic Programming
After installation, the ECU automatically learns and saves the required vehicle data. No additional programming is normally required.
e) Plug & Play – 1:1 Clone
The data from your original ECU is copied to another fully functional ECU. The cloned unit is then ready for installation without additional programming.
You must send us your original ECU so that we can transfer its data to the replacement unit.
The original ECU must have working communication with the vehicle, a diagnostic tool or our programming equipment. If the required data cannot be read, a complete 1:1 clone may not be possible.
3. Complete Plug & Play Set
A complete matched set containing the ECU, immobilizer components and all other parts required to start the vehicle without additional programming. All components supplied in the set must be installed in the vehicle.
Important:
Dispatch time depends on the selected option. If an unlocked or specially prepared version is ordered, the preparation service usually requires an additional 1–2 business days.
Ask about the product
ECU Engine controller CITROEN PEUGEOT 3.0 S101700101K
Administratorem danych osobowych jest Auto24parts. Przetwarzamy je w celu przesłania odpowiedzi na zapytanie. Więcej informacji dotyczących przetwarzania danych osobowych znajduje się w polityce prywatności.
Shipping
from
€30.00
-
shipping
(Poland)
from
€30.00
-
shipping
(Poland)
Price 30 euros applies shipments to 5 kg on worldwide. Above this weight, please contact us by email to check price
Shipping cost for the selected product
The shipping cost applies to this product (in the selected variant - if applicable). It may change after adding other products to the cart.
Engine ECU Controller Citroen Peugeot 3.0 Siemens S101700101K
Engine controller S101700101K is a proven part that helps restore proper and stable operation of the 3.0 engine in Citroen and Peugeot vehicles.
ECU ENGINE CONTROLLER CITROEN PEUGEOT 3.0 SIEMENS S101700101 K, S101700101K
Below you will find short information about the Siemens engine controller with numbers S101700101 K and S101700101K, used in 3.0 engines in Citroen and Peugeot vehicles.
Which models is the controller S101700101 K compatible with?
This controller is used in selected Citroen and Peugeot models equipped with 3.0 engines. The numbers S101700101 K and S101700101K refer to the same part. It is best to confirm compatibility using the VIN number. This is the safest way to choose the correct module.
Are S101700101 K and S101700101K the same controller?
Yes, both designations refer to the same control module. They differ only in the way the number is written. The markings come from vehicle manufacturers and the electronics supplier. The controllers are fully interchangeable.
What symptoms may indicate a failure of this controller?
The most common problems involve difficulty starting the engine. The vehicle may run unevenly or lose power. Sometimes there is no diagnostic communication. Such symptoms often indicate a problem with the controller.
Does this controller require programming after installation?
In many cases it is necessary to match it to the specific vehicle. This usually includes immobilizer configuration or ECU parameter settings. The process is carried out by an automotive electronics specialist. After programming the module works correctly.
