Vendors's code:
Product code: 4145-92950
Barcode:
Code 39:
ISBN:
Select a product option:
Individual variants may differ in price
Important: Depending on the ECU type and vehicle model, not all of the options listed below may be available.
To select the correct option for your vehicle and ECU, please contact us before purchasing:
contact@auto24parts.com
1. Locked
This option is intended for professional workshops with the required specialist equipment and technical knowledge.
The ECU has been removed from a vehicle intended for recycling and still contains the immobilizer data and other information from the previous vehicle. Before it can be used in another car, it must be unlocked and then programmed using specialist automotive diagnostic equipment.
2. Unlocked
Several preparation methods may be available. The possible options depend on the ECU type, vehicle model and immobilizer system. Please contact us before purchasing, as some preparation methods are not available for every ECU.
Our electronics specialists can prepare the ECU in one of the following ways:
a) ECU with PIN code (Car Pass)
The PIN code is supplied, but programming with a suitable diagnostic tool is still required. After installing the ECU, it must be reset using the supplied PIN code and then programmed to the vehicle’s immobilizer system.
b) VIRGIN ECU
The data from the previous vehicle is removed and the ECU is restored to a clean, factory-like state. After installation, it must be programmed to the vehicle using a compatible specialist diagnostic tool. Unless another preparation method is specified in the product description, this is the standard unlocking option for most of our ECUs.
c) Plug & Play – IMMO OFF
The immobilizer function is disabled in the ECU. After installation, the engine can start without additional immobilizer programming. Please note that the vehicle will no longer have an active immobilizer function, and an immobilizer warning light or fault code may remain, depending on the vehicle model.
d) Plug & Play – Automatic Programming
After installation, the ECU automatically learns and saves the required vehicle data. No additional programming is normally required.
e) Plug & Play – 1:1 Clone
The data from your original ECU is copied to another fully functional ECU. The cloned unit is then ready for installation without additional programming.
You must send us your original ECU so that we can transfer its data to the replacement unit.
The original ECU must have working communication with the vehicle, a diagnostic tool or our programming equipment. If the required data cannot be read, a complete 1:1 clone may not be possible.
3. Complete Plug & Play Set
A complete matched set containing the ECU, immobilizer components and all other parts required to start the vehicle without additional programming. All components supplied in the set must be installed in the vehicle.
Important:
Dispatch time depends on the selected option. If an unlocked or specially prepared version is ordered, the preparation service usually requires an additional 1–2 business days.
Administratorem danych osobowych jest Auto24parts. Przetwarzamy je w celu przesłania odpowiedzi na zapytanie. Więcej informacji dotyczących przetwarzania danych osobowych znajduje się w polityce prywatności.
Price 30 euros applies shipments to 5 kg on worldwide. Above this weight, please contact us by email to check price
The shipping cost applies to this product (in the selected variant - if applicable). It may change after adding other products to the cart.
The engine control unit 0281035648 and 5802338412 is a high-quality component intended for Iveco. It ensures stable and correct operation of the power unit, supporting optimal vehicle performance.
The engine control unit 0281035648 is responsible for electronic management of the power unit. It analyzes data from sensors (including temperature, pressure, crankshaft position) and based on this controls fuel quantity, injection timing and combustion parameters. Thanks to this, the vehicle maintains proper driving dynamics and optimal fuel consumption.
Yes, the designations 5802338412 and 0281035648 refer to the same type of engine control unit used in selected Iveco models. Differences in notation result from manufacturer numbering and catalog systems.
The engine computer 5802338412 was installed in selected Iveco vehicle versions – application depends on the specific engine, production year and equipment configuration. The safest way is to confirm compatibility by VIN number or compare the designation with the currently installed module.
You should verify the number located on the housing of the old control unit. If it shows 0281035648 or the corresponding number 5802338412, it means compatibility with the vehicle installation. In case of doubt, it is worth sending us a photo of the identification plate.
Entering the complete number, e.g. 0281035648, helps avoid mistakes when selecting the engine control unit. It is also worth checking the search variant by number 5802338412, as different catalogs and stores may use a different notation.
In most cases, after replacing the engine control unit 5802338412, adaptation or synchronization with the immobilizer is required. This process ensures proper ECU communication with vehicle systems and enables engine start.
Typical symptoms include starting problems, no response to the accelerator pedal, engine emergency mode or recurring diagnostic errors. In such situations, replacement with a working control unit 0281035648 often restores proper vehicle operation.
If the engine control unit 5802338412 is in stock, orders are usually processed within 24–48 hours. The current shipping time is always visible in the offer details.
In case of incompatibility, please contact us with the part number and vehicle details. We will help verify compatibility of control unit 0281035648 or propose the correct solution matched to the specific Iveco version.
Cookies and related technologies enable the website to function properly and help us tailor the offer to your needs. You can accept our use of all these files and go to the store or adjust the use of files to your preferences by selecting the "Customize consents" option.
Here you can specify your preferences regarding our use of cookies.
These files are necessary for the operation of our website, so you cannot disable them.
These files enable you to use other functions of the website (other than those necessary for its operation). Enabling them will give you access to the full functionality of the website.
These files allow us to analyze our online store, which may contribute to its better functioning and adaptation to the needs of Users.
Thanks to these files, we can conduct marketing activities.
