A faulty transmission control module (TCM) most often causes limp mode with the gearbox stuck in one gear, harsh jolts when you select D or R, erratic gear changes, flashing PRND letters and a gearbox or engine warning light. However, the same symptoms are often caused by a low gearbox oil level, a weak battery, a poor earth or a faulty sensor. To test a transmission control module, start by checking the battery and reading the fault codes with a diagnostic tool that can talk to the gearbox control unit, then check the power supply, the connector, the oil and the live data. Below we explain the symptoms, the diagnostic steps and what the most common fault codes mean.
ABS pump Ford Bosch RK312B373AE 0265311134 0265957322
Vendors's code: RK312B373AE
Product code: 0265957322
Barcode:
Code 39:
ISBN:
2 276,42 zł
Price
2 276,42 zł
2 800,00 zł
Price
2 800,00 zł
Select a product option:
Individual variants may differ in price
product option
Important: Depending on the ECU type and vehicle model, not all of the options listed below may be available.
To select the correct option for your vehicle and ECU, please contact us before purchasing:
contact@auto24parts.com
1. Locked
This option is intended for professional workshops with the required specialist equipment and technical knowledge.
The ECU has been removed from a vehicle intended for recycling and still contains the immobilizer data and other information from the previous vehicle. Before it can be used in another car, it must be unlocked and then programmed using specialist automotive diagnostic equipment.
2. Unlocked
Several preparation methods may be available. The possible options depend on the ECU type, vehicle model and immobilizer system. Please contact us before purchasing, as some preparation methods are not available for every ECU.
Our electronics specialists can prepare the ECU in one of the following ways:
a) ECU with PIN code (Car Pass)
The PIN code is supplied, but programming with a suitable diagnostic tool is still required. After installing the ECU, it must be reset using the supplied PIN code and then programmed to the vehicle’s immobilizer system.
b) VIRGIN ECU
The data from the previous vehicle is removed and the ECU is restored to a clean, factory-like state. After installation, it must be programmed to the vehicle using a compatible specialist diagnostic tool. Unless another preparation method is specified in the product description, this is the standard unlocking option for most of our ECUs.
c) Plug & Play – IMMO OFF
The immobilizer function is disabled in the ECU. After installation, the engine can start without additional immobilizer programming. Please note that the vehicle will no longer have an active immobilizer function, and an immobilizer warning light or fault code may remain, depending on the vehicle model.
d) Plug & Play – Automatic Programming
After installation, the ECU automatically learns and saves the required vehicle data. No additional programming is normally required.
e) Plug & Play – 1:1 Clone
The data from your original ECU is copied to another fully functional ECU. The cloned unit is then ready for installation without additional programming.
You must send us your original ECU so that we can transfer its data to the replacement unit.
The original ECU must have working communication with the vehicle, a diagnostic tool or our programming equipment. If the required data cannot be read, a complete 1:1 clone may not be possible.
3. Complete Plug & Play Set
A complete matched set containing the ECU, immobilizer components and all other parts required to start the vehicle without additional programming. All components supplied in the set must be installed in the vehicle.
Important:
Dispatch time depends on the selected option. If an unlocked or specially prepared version is ordered, the preparation service usually requires an additional 1–2 business days.
Ask about the product
ABS pump Ford Bosch RK312B373AE 0265311134 0265957322
Administratorem danych osobowych jest Auto24parts. Przetwarzamy je w celu przesłania odpowiedzi na zapytanie. Więcej informacji dotyczących przetwarzania danych osobowych znajduje się w polityce prywatności.
Shipping
from
120,00 zł
-
shipping
(Poland)
from
120,00 zł
-
shipping
(Poland)
Price 30 euros applies shipments to 5 kg on worldwide. Above this weight, please contact us by email to check price
Shipping cost for the selected product
The shipping cost applies to this product (in the selected variant - if applicable). It may change after adding other products to the cart.
Where to find number RK312B373AE on Ford ABS pumps
Used ABS pump with control unit, number RK312B373AE, inspected before sale. Matched by the numbers on the block and sticker.
Used Ford ABS pump with number RK312B373AE
If the ABS warning light is on in your Ford, one possible cause is the hydraulic module or its control unit. ABS pump RK312B373AE is a used original part, inspected before sale. The listing does not state the car model or year, so we do not give them here and match the part by its numbers.
Where to find the numbers on an ABS pump
The numbers from the listing, as written on the labels and as a single string:
- RK312B373AE, original Ford number,
- 0 265 311 134 (catalogue format: 0265311134), hydraulic block manufacturer's number,
- 0 265 957 322 (catalogue format: 0265957322), control unit number.
The full numbers matter, including their endings. If in doubt, send us a photo of your pump.
Symptoms of a faulty ABS pump or control unit
- the brake pedal pulses or feels uneven for no obvious reason,
- the pump motor switches on at unusual moments or runs louder than usual,
- the ABS switches itself off shortly after the engine is started,
- on a slippery surface the wheels lock up noticeably sooner than they used to.
ABS faults should not be ignored, because without anti-lock protection the car brakes less well on wet or slippery roads. Diagnosis and fitting are best left to a garage with a suitable scanner.
Questions and answers
| Where do I find number RK312B373AE on my pump? |
|---|
| The numbers are stamped or printed on the aluminium hydraulic block, and the control unit has a separate sticker. Take a close-up photo of both places in good light. |
| Which car model does this pump fit? |
| The listing does not state a model or year, so confirm compatibility with the number from the original pump in your car, or send us a photo of it. |
| Do the brakes need bleeding after replacing the module? |
| If the brake lines are disconnected during fitting, the system must be bled. The fault codes in the control unit usually need to be cleared as well. |
| What condition is this ABS module in? |
| It is an original recycled part in good condition, checked by us. Warranty details are in the product features table. |
Not certain this is the right module? Send us the numbers from the label on your pump and we will help you compare them.
