A faulty transmission control module (TCM) most often causes limp mode with the gearbox stuck in one gear, harsh jolts when you select D or R, erratic gear changes, flashing PRND letters and a gearbox or engine warning light. However, the same symptoms are often caused by a low gearbox oil level, a weak battery, a poor earth or a faulty sensor. To test a transmission control module, start by checking the battery and reading the fault codes with a diagnostic tool that can talk to the gearbox control unit, then check the power supply, the connector, the oil and the live data. Below we explain the symptoms, the diagnostic steps and what the most common fault codes mean.
Fuel Injection Control Module Toyota Avensis 2.0 8987120070 1310001371
Vendors's code: 89871-20070
Product code: 6AC3-3099C
Barcode:
Code 39:
ISBN:
£92.27
Price
£92.27
£113.49
Price
£113.49
In stock
Select a product option:
Individual variants may differ in price
product option
Important: Depending on the ECU type and vehicle model, not all of the options listed below may be available.
To select the correct option for your vehicle and ECU, please contact us before purchasing:
contact@auto24parts.com
1. Locked
This option is intended for professional workshops with the required specialist equipment and technical knowledge.
The ECU has been removed from a vehicle intended for recycling and still contains the immobilizer data and other information from the previous vehicle. Before it can be used in another car, it must be unlocked and then programmed using specialist automotive diagnostic equipment.
2. Unlocked
Several preparation methods may be available. The possible options depend on the ECU type, vehicle model and immobilizer system. Please contact us before purchasing, as some preparation methods are not available for every ECU.
Our electronics specialists can prepare the ECU in one of the following ways:
a) ECU with PIN code (Car Pass)
The PIN code is supplied, but programming with a suitable diagnostic tool is still required. After installing the ECU, it must be reset using the supplied PIN code and then programmed to the vehicle’s immobilizer system.
b) VIRGIN ECU
The data from the previous vehicle is removed and the ECU is restored to a clean, factory-like state. After installation, it must be programmed to the vehicle using a compatible specialist diagnostic tool. Unless another preparation method is specified in the product description, this is the standard unlocking option for most of our ECUs.
c) Plug & Play – IMMO OFF
The immobilizer function is disabled in the ECU. After installation, the engine can start without additional immobilizer programming. Please note that the vehicle will no longer have an active immobilizer function, and an immobilizer warning light or fault code may remain, depending on the vehicle model.
d) Plug & Play – Automatic Programming
After installation, the ECU automatically learns and saves the required vehicle data. No additional programming is normally required.
e) Plug & Play – 1:1 Clone
The data from your original ECU is copied to another fully functional ECU. The cloned unit is then ready for installation without additional programming.
You must send us your original ECU so that we can transfer its data to the replacement unit.
The original ECU must have working communication with the vehicle, a diagnostic tool or our programming equipment. If the required data cannot be read, a complete 1:1 clone may not be possible.
3. Complete Plug & Play Set
A complete matched set containing the ECU, immobilizer components and all other parts required to start the vehicle without additional programming. All components supplied in the set must be installed in the vehicle.
Important:
Dispatch time depends on the selected option. If an unlocked or specially prepared version is ordered, the preparation service usually requires an additional 1–2 business days.
Ask about the product
Fuel Injection Control Module Toyota Avensis 2.0 8987120070 1310001371
Administratorem danych osobowych jest Auto24parts. Przetwarzamy je w celu przesłania odpowiedzi na zapytanie. Więcej informacji dotyczących przetwarzania danych osobowych znajduje się w polityce prywatności.
Shipping
from
£22.70
-
shipping
(Poland)
from
£22.70
-
shipping
(Poland)
Price 30 euros applies shipments to 5 kg on worldwide. Above this weight, please contact us by email to check price
Shipping cost for the selected product
The shipping cost applies to this product (in the selected variant - if applicable). It may change after adding other products to the cart.
Injector control module Toyota Avensis 2.0 8987120070 1310001371
The injector control module for Toyota Avensis 2.0 with part numbers 8987120070 and 1310001371 is a suitable solution when replacing a damaged component – before purchasing, make sure the part numbers match your vehicle to ensure proper compatibility.
What does the number 8987120070 mean on a Toyota Avensis 2.0 injector control unit?
The number 8987120070 identifies a specific injector control module used in the Toyota Avensis 2.0. This designation allows precise matching of the part to the correct engine version.
Does the injector module 1310001371 fit my Toyota Avensis?
To confirm compatibility of the 1310001371 control unit, compare the number with the marking on the original module installed in your vehicle. Full number matching is essential for proper engine operation.
What function does the injector computer 8987120070 perform?
The control unit with number 8987120070 manages the fuel injection system in the Toyota Avensis 2.0. It controls fuel dosing and directly affects engine stability and performance.
What symptoms may indicate a problem with the 1310001371 module?
Uneven engine operation, difficulty starting, or loss of power may indicate a fault in the 1310001371 injector module. Replacing it with a functional unit often restores proper performance.
Why is the number 8987120070 so important when choosing a control unit?
Injector control units may look similar, but the exact number 8987120070 determines compatibility with a specific Toyota Avensis 2.0 engine version.
Does the 1310001371 computer require programming after installation?
Depending on the engine version, the 1310001371 module may require adaptation after installation. It is advisable to verify whether additional configuration is necessary before fitting.
How can I check compatibility of the 8987120070 control unit?
The simplest method is to compare the number 8987120070 with the marking on your old part. Matching numbers minimizes the risk of incorrect fitment.
Why search for the part by the number 1310001371?
Entering the exact number 1310001371 in a search engine helps quickly find the correct injector module for Toyota Avensis 2.0. It is the most precise method of part selection.
What should I check before ordering the 8987120070 control unit?
Before purchasing, make sure that the numbers 8987120070 and 1310001371 fully match the markings on your current part. Verifying compatibility helps avoid post-installation issues.
Is the injector module 1310001371 available in different variants?
Depending on the production year of the Toyota Avensis 2.0, the 1310001371 module may be available in different versions. It is recommended to carefully review the product description before purchase.
