A properly functioning ABS system is the foundation of road safety. Its main task is to prevent wheel lock-up during emergency braking, which allows the driver to maintain full control of the vehicle. The heart of this system is the electronic ABS pump controller. When it fails, the system stops working. A proper diagnosis of the problem allows you to avoid unnecessary costs and quickly restore brake efficiency.
ECU Engine Controller MITSUBISHI LANCER BOSCH 0 281 014 586 0281014586 1860A579 60A579 1860A57960A579
Vendors's code:
Product code: 5DAB-10630
Barcode:
Code 39:
ISBN:
€101.63
Price
€101.63
Regular price:
€101.63
0%
€125.00
Price
€125.00
Regular price:
€125.00
0%
In stock
Select a product option:
Individual variants may differ in price
product option
Important: Depending on the ECU type and vehicle model, not all of the options listed below may be available.
To select the correct option for your vehicle and ECU, please contact us before purchasing:
contact@auto24parts.com
1. Locked
This option is intended for professional workshops with the required specialist equipment and technical knowledge.
The ECU has been removed from a vehicle intended for recycling and still contains the immobilizer data and other information from the previous vehicle. Before it can be used in another car, it must be unlocked and then programmed using specialist automotive diagnostic equipment.
2. Unlocked
Several preparation methods may be available. The possible options depend on the ECU type, vehicle model and immobilizer system. Please contact us before purchasing, as some preparation methods are not available for every ECU.
Our electronics specialists can prepare the ECU in one of the following ways:
a) ECU with PIN code (Car Pass)
The PIN code is supplied, but programming with a suitable diagnostic tool is still required. After installing the ECU, it must be reset using the supplied PIN code and then programmed to the vehicle’s immobilizer system.
b) VIRGIN ECU
The data from the previous vehicle is removed and the ECU is restored to a clean, factory-like state. After installation, it must be programmed to the vehicle using a compatible specialist diagnostic tool. Unless another preparation method is specified in the product description, this is the standard unlocking option for most of our ECUs.
c) Plug & Play – IMMO OFF
The immobilizer function is disabled in the ECU. After installation, the engine can start without additional immobilizer programming. Please note that the vehicle will no longer have an active immobilizer function, and an immobilizer warning light or fault code may remain, depending on the vehicle model.
d) Plug & Play – Automatic Programming
After installation, the ECU automatically learns and saves the required vehicle data. No additional programming is normally required.
e) Plug & Play – 1:1 Clone
The data from your original ECU is copied to another fully functional ECU. The cloned unit is then ready for installation without additional programming.
You must send us your original ECU so that we can transfer its data to the replacement unit.
The original ECU must have working communication with the vehicle, a diagnostic tool or our programming equipment. If the required data cannot be read, a complete 1:1 clone may not be possible.
3. Complete Plug & Play Set
A complete matched set containing the ECU, immobilizer components and all other parts required to start the vehicle without additional programming. All components supplied in the set must be installed in the vehicle.
Important:
Dispatch time depends on the selected option. If an unlocked or specially prepared version is ordered, the preparation service usually requires an additional 1–2 business days.
Ask about the product
ECU Engine Controller MITSUBISHI LANCER BOSCH 0 281 014 586 0281014586 1860A579 60A579 1860A57960A579
Administratorem danych osobowych jest Auto24parts. Przetwarzamy je w celu przesłania odpowiedzi na zapytanie. Więcej informacji dotyczących przetwarzania danych osobowych znajduje się w polityce prywatności.
Shipping
from
€30.00
-
shipping
(Poland)
from
€30.00
-
shipping
(Poland)
Price 30 euros applies shipments to 5 kg on worldwide. Above this weight, please contact us by email to check price
Shipping cost for the selected product
The shipping cost applies to this product (in the selected variant - if applicable). It may change after adding other products to the cart.
Mitsubishi Lancer ECU Engine Controller Bosch 0281014586 / 1860A579
The ECU engine controller 0 281 014 586, 0281014586, 1860A579 and 60A579 is a proven Bosch part that ensures stable and proper engine operation in the Mitsubishi Lancer.
What function does the Bosch 0281014586 Ecu engine controller perform in the Mitsubishi Lancer?
The Ecu engine controller identified by the numbers 0 281 014 586 and 0281014586 controls the operation of the power unit in the Mitsubishi Lancer. It manages fuel injection, combustion parameters and cooperation with sensors, directly affecting smooth driving and correct engine operation.
In which Mitsubishi Lancer versions is this Ecu engine controller used?
This Ecu engine controller was used in selected versions of the Mitsubishi Lancer. Exact application depends on production year and engine variant, therefore ECU number or VIN verification is recommended before purchase.
How can I confirm that the 1860A579 Ecu engine controller fits my vehicle?
The best way is to check the markings on the installed unit. If the numbers 1860A579, 60A579 or the Bosch number 0281014586 are present, the Ecu engine controller is compatible. You can also send us a photo for verification.
Why does this Ecu engine controller have multiple part numbers?
Numbers such as 1860A579, 60A579 and 0281014586 come from different numbering systems of the vehicle manufacturer and the electronics supplier. All refer to the same Ecu engine controller.
Does the Bosch Ecu engine controller require programming after replacement?
After installation, the Ecu engine controller usually requires adaptation, programming or cloning to work correctly with the immobilizer and vehicle electronics. This is a standard ECU replacement procedure.
