A properly functioning ABS system is the foundation of road safety. Its main task is to prevent wheel lock-up during emergency braking, which allows the driver to maintain full control of the vehicle. The heart of this system is the electronic ABS pump controller. When it fails, the system stops working. A proper diagnosis of the problem allows you to avoid unnecessary costs and quickly restore brake efficiency.
ECU Engine controller PEUGEOT 406 1.8 SAGEM 21658467-4 9640248480
Vendors's code: 216584674
Product code: 9640248480
Barcode:
Code 39:
ISBN:
€81.30
Price
€81.30
Regular price:
€81.30
0%
€100.00
Price
€100.00
Regular price:
€100.00
0%
Select a product option:
Individual variants may differ in price
product option
Important: Depending on the ECU type and vehicle model, not all of the options listed below may be available.
To select the correct option for your vehicle and ECU, please contact us before purchasing:
contact@auto24parts.com
1. Locked
This option is intended for professional workshops with the required specialist equipment and technical knowledge.
The ECU has been removed from a vehicle intended for recycling and still contains the immobilizer data and other information from the previous vehicle. Before it can be used in another car, it must be unlocked and then programmed using specialist automotive diagnostic equipment.
2. Unlocked
Several preparation methods may be available. The possible options depend on the ECU type, vehicle model and immobilizer system. Please contact us before purchasing, as some preparation methods are not available for every ECU.
Our electronics specialists can prepare the ECU in one of the following ways:
a) ECU with PIN code (Car Pass)
The PIN code is supplied, but programming with a suitable diagnostic tool is still required. After installing the ECU, it must be reset using the supplied PIN code and then programmed to the vehicle’s immobilizer system.
b) VIRGIN ECU
The data from the previous vehicle is removed and the ECU is restored to a clean, factory-like state. After installation, it must be programmed to the vehicle using a compatible specialist diagnostic tool. Unless another preparation method is specified in the product description, this is the standard unlocking option for most of our ECUs.
c) Plug & Play – IMMO OFF
The immobilizer function is disabled in the ECU. After installation, the engine can start without additional immobilizer programming. Please note that the vehicle will no longer have an active immobilizer function, and an immobilizer warning light or fault code may remain, depending on the vehicle model.
d) Plug & Play – Automatic Programming
After installation, the ECU automatically learns and saves the required vehicle data. No additional programming is normally required.
e) Plug & Play – 1:1 Clone
The data from your original ECU is copied to another fully functional ECU. The cloned unit is then ready for installation without additional programming.
You must send us your original ECU so that we can transfer its data to the replacement unit.
The original ECU must have working communication with the vehicle, a diagnostic tool or our programming equipment. If the required data cannot be read, a complete 1:1 clone may not be possible.
3. Complete Plug & Play Set
A complete matched set containing the ECU, immobilizer components and all other parts required to start the vehicle without additional programming. All components supplied in the set must be installed in the vehicle.
Important:
Dispatch time depends on the selected option. If an unlocked or specially prepared version is ordered, the preparation service usually requires an additional 1–2 business days.
Ask about the product
ECU Engine controller PEUGEOT 406 1.8 SAGEM 21658467-4 9640248480
Administratorem danych osobowych jest Auto24parts. Przetwarzamy je w celu przesłania odpowiedzi na zapytanie. Więcej informacji dotyczących przetwarzania danych osobowych znajduje się w polityce prywatności.
Shipping
from
€30.00
-
shipping
(Poland)
from
€30.00
-
shipping
(Poland)
Price 30 euros applies shipments to 5 kg on worldwide. Above this weight, please contact us by email to check price
Shipping cost for the selected product
The shipping cost applies to this product (in the selected variant - if applicable). It may change after adding other products to the cart.
9640248480 21658467-4 SAGEM 1.8 Peugeot 406 engine controller
Original ECU ENGINE CONTROLLER for Peugeot 406 1.8, professionally inspected and available with secure worldwide shipping.
FAQ – Peugeot 406 1.8 engine controller SAGEM 21658467-4 / 9640248480
Is the SAGEM 21658467-4 controller compatible with Peugeot 406 1.8?
Yes, this engine controller is designed for Peugeot 406 vehicles equipped with the 1.8 engine, provided that the part numbers match. Before purchasing, compare the 21658467-4 reference and the 9640248480 number with the module currently installed in the vehicle.
Why is part number 9640248480 important when selecting an ECU?
The 9640248480 reference allows accurate identification of the correct engine controller for a specific vehicle version. For ECUs, matching the part number is essential for proper engine operation, communication with the vehicle systems and trouble-free installation.
What are the characteristics of the SAGEM engine controller for Peugeot 406?
The SAGEM controller manages engine operation, fuel delivery and ignition parameters. The version marked 21658467-4 was used in selected Peugeot 406 1.8 models, so the safest way to choose a replacement is by comparing the numbers on the unit.
Can I install an ECU with a different number than 21658467-4?
Installing a controller with a different reference is not recommended. Even if the unit looks identical, software differences may lead to starting issues or engine performance problems. The safest option is to use a controller matching SAGEM 21658467-4 or 9640248480.
How can I check whether this engine controller is suitable for my vehicle?
Read the numbers from the original controller installed in the vehicle and compare them with the offered unit. If the references 9640248480 or 21658467-4 are present, this Peugeot 406 1.8 engine controller may be the correct replacement.
