Skip to main content
English €
English €
Open search engine
Search
Close search engine Clear Search
Open search engine
Search
Close search engine Clear Search
English €
English €
Products in the cart: 0. See details
Open search engine
Search
Close search engine Clear Search

Seat belt pretensioner Opel Vectra C, left front 24463508F, L9021510469

  • Part Type Seat belt pretensioner
  • Vehicle Make and Model Opel Vectra C
  • OEM Part Number 24463508F, L9021510469
  • Condition Used part
GM
with VAT without VAT
Price €17.50
Availability:
In stock
pcs.

Fast Delivery

DHL Express - 30 euro

6 Month Warranty

Returns Possible up to 14 days

Secure payments

Stripe - Paypal - Credit Card
Ask about the product
Shipping from €30.00 - shipping (Poland)

Price 30 euros applies shipments to 5 kg on worldwide. Above this weight, please contact us by email to check price


PRODUCT DETAILS

  • Part Type Seat belt pretensioner
  • Vehicle Make and Model Opel Vectra C
  • OEM Part Number 24463508F, L9021510469
  • Condition Used part

Seat belt pretensioner 24463508F – how to confirm the fit?

Seat belt pretensioner, number 24463508F, application: Opel Vectra C. This is a used part. The safest way to match it is by the number on the label or housing.

Go to full description

Seat belt pretensioner Opel Vectra C, left front 24463508F, L9021510469

The seat belt pretensioner 24463508F is a part used in Opel Vectra C. This is a used part. Shipping or personal collection is available.

Part numbers

  • 24463508F – OEM number
  • L9021510469 – OEM number
  • side and position: left front

Application according to the listing

  • make and model: Opel Vectra C

One car model may have used different versions of this part, so the number matters most.

How this part works

The airbag control unit decides when the pretensioner fires, based on signals from the crash sensors.

Possible fault symptoms

These symptoms may point to a fault:

  • the airbag light is on and the diagnosis points to the pretensioner circuit,
  • the pretensioner connector or wiring is damaged,
  • the car is being repaired after a crash in which the airbags deployed.

Fitting – what to watch out for

Compare the number, side and position of the pretensioner with the part removed from the car. After fitting, clear the airbag fault codes and check that the warning light goes out when you switch on the ignition.

Frequently asked questions

Can I ask about the fit before ordering?
Yes. Send us the number of your part and your car details (VIN, engine code, year) and we will check the fit.
How can I receive my order?
Shipping or personal collection is available.

Not sure which number is right? Send a photo of the label to contact@auto24parts.com and we will help.

  • How to Check the Operation of a Transmission Control Module - Symptoms

    A faulty transmission control module (TCM) most often causes limp mode with the gearbox stuck in one gear, harsh jolts when you select D or R, erratic gear changes, flashing PRND letters and a gearbox or engine warning light. However, the same symptoms are often caused by a low gearbox oil level, a weak battery, a poor earth or a faulty sensor. To test a transmission control module, start by checking the battery and reading the fault codes with a diagnostic tool that can talk to the gearbox control unit, then check the power supply, the connector, the oil and the live data. Below we explain the symptoms, the diagnostic steps and what the most common fault codes mean.

    Read more
  • Burned Engine Control Unit: Symptoms, Causes, and the Optimal Solution

    A burned engine control unit (ECU) usually causes a sudden no-start: the engine cranks but will not start, the diagnostic tool cannot connect to the ECU, and the engine management light does not come on when you switch on the ignition. The most common causes are a voltage spike when jump-starting, reversed battery polarity, a faulty voltage regulator and a short circuit in the wiring loom or in an actuator. Below we explain how to tell a burned ECU from a power supply fault, what causes this kind of failure and how to choose a replacement ECU.

    Read more
  • Flooded Automatic Transmission Control Module or Burnt TCM - Symptoms

    A burnt-out or flooded automatic transmission control module (TCM) usually causes sudden symptoms: limp mode with the gearbox stuck in one gear, harsh thumps when you select D or R, no response to the gear selector, flashing or blank PRND letters and no communication between the diagnostic tool and the gearbox control unit. Flooding is most often caused by blocked scuttle panel drains, washing the engine bay or coolant in the gearbox oil, and a burnout by overheating, a short circuit or a voltage spike. Below we explain the symptoms, what to do straight away and why drying out or repairing such a control unit rarely gives a lasting result.

    Read more
  • Flooded engine control unit - symptoms, consequences and what to do

    A flooded engine control unit (ECU) most often causes a no-start, a 'Christmas tree' of warning lights on the dashboard, no communication with the diagnostic tool, or rough running in limp mode. Water usually gets into the ECU from blocked scuttle drains, after the engine bay has been cleaned with a pressure washer, or after driving through deep water. Below we describe the symptoms of a water-damaged ECU, what to do straight after the ECU gets wet, and why drying or repairing it rarely gives lasting results.

    Read more