Skip to main content
English €
English €
Open search engine
Search
Close search engine Clear Search
Open search engine
Search
Close search engine Clear Search
English €
English €
Products in the cart: 0. See details
Open search engine
Search
Close search engine Clear Search

Seat belt pretensioner Opel Vectra, left rear 24463289F, C9021120340

  • Part Type Seat belt pretensioner
  • Vehicle Make and Model Opel Vectra
  • OEM Part Number 24463289F, C9021120340
  • Condition Used part
GM
with VAT without VAT
Price €10.00
Availability:
In stock
pcs.

Fast Delivery

DHL Express - 30 euro

6 Month Warranty

Returns Possible up to 14 days

Secure payments

Stripe - Paypal - Credit Card
Ask about the product
Shipping from €30.00 - shipping (Poland)

Price 30 euros applies shipments to 5 kg on worldwide. Above this weight, please contact us by email to check price


PRODUCT DETAILS

  • Part Type Seat belt pretensioner
  • Vehicle Make and Model Opel Vectra
  • OEM Part Number 24463289F, C9021120340
  • Condition Used part

Does the seat belt pretensioner 24463289F fit your car?

This is a seat belt pretensioner with the number 24463289F for Opel Vectra. This is a used part. Before ordering, compare the number with the one on your part.

Go to full description

Seat belt pretensioner Opel Vectra, left rear 24463289F, C9021120340

We offer a seat belt pretensioner with the number 24463289F. According to the listing data it fits Opel Vectra. This is a used part. Shipping or personal collection is available.

Part numbers

  • 24463289F – OEM number
  • C9021120340 – OEM number
  • side and position: left rear

Its role in the safety system

The airbag control unit decides when the pretensioner fires, based on signals from the crash sensors.

Application according to the listing

  • make and model: Opel Vectra

One car model may have used different versions of this part, so the number matters most.

When a replacement may be needed

It is worth checking the part when:

  • the pretensioner fired in a collision,
  • the belt does not retract or locks for no reason,
  • the pretensioner connector or wiring is damaged.

Fitting – what to watch out for

Compare the number, side and position of the pretensioner with the part removed from the car. After fitting, clear the airbag fault codes and check that the warning light goes out when you switch on the ignition.

Questions and answers

What condition is the part in?
This is a used part. The photos in the listing show the actual item.
Can I ask about the fit before ordering?
Yes. Send us the number of your part and your car details (VIN, engine code, year) and we will check the fit.
Do I need to clear the airbag fault after replacing the pretensioner?
Yes. After fitting, clear the fault codes in the airbag control unit with a diagnostic tester and check that the warning light goes out a few seconds after you switch on the ignition.

Order online or write to contact@auto24parts.com if you want to confirm the fit.

  • How to Check the Operation of a Transmission Control Module - Symptoms

    A faulty transmission control module (TCM) most often causes limp mode with the gearbox stuck in one gear, harsh jolts when you select D or R, erratic gear changes, flashing PRND letters and a gearbox or engine warning light. However, the same symptoms are often caused by a low gearbox oil level, a weak battery, a poor earth or a faulty sensor. To test a transmission control module, start by checking the battery and reading the fault codes with a diagnostic tool that can talk to the gearbox control unit, then check the power supply, the connector, the oil and the live data. Below we explain the symptoms, the diagnostic steps and what the most common fault codes mean.

    Read more
  • Burned Engine Control Unit: Symptoms, Causes, and the Optimal Solution

    A burned engine control unit (ECU) usually causes a sudden no-start: the engine cranks but will not start, the diagnostic tool cannot connect to the ECU, and the engine management light does not come on when you switch on the ignition. The most common causes are a voltage spike when jump-starting, reversed battery polarity, a faulty voltage regulator and a short circuit in the wiring loom or in an actuator. Below we explain how to tell a burned ECU from a power supply fault, what causes this kind of failure and how to choose a replacement ECU.

    Read more
  • Flooded Automatic Transmission Control Module or Burnt TCM - Symptoms

    A burnt-out or flooded automatic transmission control module (TCM) usually causes sudden symptoms: limp mode with the gearbox stuck in one gear, harsh thumps when you select D or R, no response to the gear selector, flashing or blank PRND letters and no communication between the diagnostic tool and the gearbox control unit. Flooding is most often caused by blocked scuttle panel drains, washing the engine bay or coolant in the gearbox oil, and a burnout by overheating, a short circuit or a voltage spike. Below we explain the symptoms, what to do straight away and why drying out or repairing such a control unit rarely gives a lasting result.

    Read more
  • Flooded engine control unit - symptoms, consequences and what to do

    A flooded engine control unit (ECU) most often causes a no-start, a 'Christmas tree' of warning lights on the dashboard, no communication with the diagnostic tool, or rough running in limp mode. Water usually gets into the ECU from blocked scuttle drains, after the engine bay has been cleaned with a pressure washer, or after driving through deep water. Below we describe the symptoms of a water-damaged ECU, what to do straight after the ECU gets wet, and why drying or repairing it rarely gives lasting results.

    Read more