A properly functioning ABS system is the foundation of road safety. Its main task is to prevent wheel lock-up during emergency braking, which allows the driver to maintain full control of the vehicle. The heart of this system is the electronic ABS pump controller. When it fails, the system stops working. A proper diagnosis of the problem allows you to avoid unnecessary costs and quickly restore brake efficiency.
ECU Engine controller SEAT 2.0 TDI BOSCH 0281013283 03G906021LP EDC16U34
Vendors's code: 03G906021LP
Product code: 0281013283
Barcode:
Code 39:
ISBN:
€81.30
Price
€81.30
Regular price:
€81.30
0%
€100.00
Price
€100.00
Regular price:
€100.00
0%
Select a product option:
Individual variants may differ in price
product option
Important: Depending on the ECU type and vehicle model, not all of the options listed below may be available.
To select the correct option for your vehicle and ECU, please contact us before purchasing:
contact@auto24parts.com
1. Locked
This option is intended for professional workshops with the required specialist equipment and technical knowledge.
The ECU has been removed from a vehicle intended for recycling and still contains the immobilizer data and other information from the previous vehicle. Before it can be used in another car, it must be unlocked and then programmed using specialist automotive diagnostic equipment.
2. Unlocked
Several preparation methods may be available. The possible options depend on the ECU type, vehicle model and immobilizer system. Please contact us before purchasing, as some preparation methods are not available for every ECU.
Our electronics specialists can prepare the ECU in one of the following ways:
a) ECU with PIN code (Car Pass)
The PIN code is supplied, but programming with a suitable diagnostic tool is still required. After installing the ECU, it must be reset using the supplied PIN code and then programmed to the vehicle’s immobilizer system.
b) VIRGIN ECU
The data from the previous vehicle is removed and the ECU is restored to a clean, factory-like state. After installation, it must be programmed to the vehicle using a compatible specialist diagnostic tool. Unless another preparation method is specified in the product description, this is the standard unlocking option for most of our ECUs.
c) Plug & Play – IMMO OFF
The immobilizer function is disabled in the ECU. After installation, the engine can start without additional immobilizer programming. Please note that the vehicle will no longer have an active immobilizer function, and an immobilizer warning light or fault code may remain, depending on the vehicle model.
d) Plug & Play – Automatic Programming
After installation, the ECU automatically learns and saves the required vehicle data. No additional programming is normally required.
e) Plug & Play – 1:1 Clone
The data from your original ECU is copied to another fully functional ECU. The cloned unit is then ready for installation without additional programming.
You must send us your original ECU so that we can transfer its data to the replacement unit.
The original ECU must have working communication with the vehicle, a diagnostic tool or our programming equipment. If the required data cannot be read, a complete 1:1 clone may not be possible.
3. Complete Plug & Play Set
A complete matched set containing the ECU, immobilizer components and all other parts required to start the vehicle without additional programming. All components supplied in the set must be installed in the vehicle.
Important:
Dispatch time depends on the selected option. If an unlocked or specially prepared version is ordered, the preparation service usually requires an additional 1–2 business days.
Ask about the product
ECU Engine controller SEAT 2.0 TDI BOSCH 0281013283 03G906021LP EDC16U34
Administratorem danych osobowych jest Auto24parts. Przetwarzamy je w celu przesłania odpowiedzi na zapytanie. Więcej informacji dotyczących przetwarzania danych osobowych znajduje się w polityce prywatności.
Shipping
from
€30.00
-
shipping
(Poland)
from
€30.00
-
shipping
(Poland)
Price 30 euros applies shipments to 5 kg on worldwide. Above this weight, please contact us by email to check price
Shipping cost for the selected product
The shipping cost applies to this product (in the selected variant - if applicable). It may change after adding other products to the cart.
ECU ENGINE CONTROLLER SEAT 2.0 TDI BOSCH 0281013283 03G906021LP EDC16U34
Tested ECU Engine controller Bosch for Seat 2.0 TDI, part numbers 0281013283 and 03G906021LP (EDC16U34), with warranty and fast shipping.
ECU Engine controller SEAT 2.0 TDI BOSCH 0281013283 03G906021LP EDC16U34
Which Seat vehicles use the Bosch 0281013283 03G906021LP ECU Engine controller?
The ECU Engine controller SEAT 2.0 TDI BOSCH 0281013283 03G906021LP should be matched by the label codes on your original unit. It appears in selected Seat 2.0 TDI applications, so the safest method is to compare 0281013283 and 03G906021LP directly on the ECU label.
If your ECU shows Bosch 0281013283 and 03G906021LP and the label also mentions EDC16U34, these are the correct references for a compatible Seat replacement.
Is “0 281 013 283” the same as “0281013283”?
You may see the same Bosch number written with spaces (0 281 013 283) or as one sequence (0281013283). What matters is that the digits match your original ECU label.
For Seat fitment, it’s best to match both identifiers on the unit: 0281013283 and 03G906021LP.
What does the Seat 2.0 TDI EDC16U34 engine controller do?
The Seat 2.0 TDI EDC16U34 engine controller manages engine operation during everyday driving. It processes sensor signals and controls key parameters to keep the engine running smoothly and consistently.
The ECU identified by 0281013283 and 03G906021LP also supports proper communication with the vehicle’s electronics.
What symptoms can a faulty Bosch 0281013283 ECU cause in a Seat?
A faulty Bosch 0281013283 ECU can cause starting problems, rough running, loss of power, or recurring diagnostic errors.
Because similar symptoms can also be caused by wiring or sensors, it’s best to select the replacement strictly by 0281013283, 03G906021LP and EDC16U34.
Does the SEAT 2.0 TDI 0281013283 03G906021LP ECU need coding after installation?
Depending on the vehicle version, the SEAT 2.0 TDI 0281013283 03G906021LP ECU may require coding or adaptation after installation, especially when immobilizer functions are involved.
This ECU is tested before dispatch, covered by warranty, and shipped fast. Matching 0281013283 and 03G906021LP helps reduce post-swap issues.
