A faulty transmission control module (TCM) most often causes limp mode with the gearbox stuck in one gear, harsh jolts when you select D or R, erratic gear changes, flashing PRND letters and a gearbox or engine warning light. However, the same symptoms are often caused by a low gearbox oil level, a weak battery, a poor earth or a faulty sensor. To test a transmission control module, start by checking the battery and reading the fault codes with a diagnostic tool that can talk to the gearbox control unit, then check the power supply, the connector, the oil and the live data. Below we explain the symptoms, the diagnostic steps and what the most common fault codes mean.
ABS pump and control module Suzuki Jimny Advics 5611078RA 11604044641
Vendors's code: 5611078RA
Product code: 11604044641
Barcode:
Code 39:
ISBN:
€487.80
Price
€487.80
€600.00
Price
€600.00
Ask about the product
ABS pump and control module Suzuki Jimny Advics 5611078RA 11604044641
Administratorem danych osobowych jest Auto24parts. Przetwarzamy je w celu przesłania odpowiedzi na zapytanie. Więcej informacji dotyczących przetwarzania danych osobowych znajduje się w polityce prywatności.
Shipping
from
€30.00
-
shipping
(Poland)
from
€30.00
-
shipping
(Poland)
Price 30 euros applies shipments to 5 kg on worldwide. Above this weight, please contact us by email to check price
Shipping cost for the selected product
The shipping cost applies to this product (in the selected variant - if applicable). It may change after adding other products to the cart.
When is ABS pump 5611078RA the right choice for your Suzuki Jimny?
Used ABS pump with control unit, number 5611078RA, inspected before sale. Matched by the numbers on the block and sticker.
Suzuki Jimny ABS pump 5611078RA: hydraulic module with control unit
ABS pump 5611078RA for Suzuki Jimny is a used original module that regulates brake pressure when a wheel starts to lock up. It is matched by the numbers on its labels, not by the car model alone. According to the listing, the pump comes from the Suzuki Jimny model. Markings found on the parts (stamped or printed): 78RA. They help tell the module versions apart, but the full part number is what decides compatibility.
Where to find the numbers on an ABS pump
You will find the numbers on the labels, while catalogues list them as a single string:
- 56110-78RA (catalogue format: 5611078RA), Suzuki number stamped on the hydraulic block,
- 116040-44641 (catalogue format: 11604044641), control unit number.
Check the numbers on your pump and compare them with those above. If any of them differs, contact us before ordering.
What ABS problems can point to
- the ABS warning light comes on after the engine is started and stays on,
- the brake pedal pulses or feels uneven for no obvious reason,
- the ABS warning light comes on together with the stability control warning light,
- on a slippery surface the wheels lock up noticeably sooner than they used to.
It is worth reading the fault codes and checking the sensor wiring before replacement. Fitting and bleeding the brake system are usually carried out by a garage with the right equipment.
Questions and answers
| Does a lit ABS warning light always mean a faulty pump? |
|---|
| No. Read the fault codes first, because the cause may be a wheel sensor, its wiring or too low a supply voltage. |
| Do the brakes need bleeding after replacing the module? |
| If the brake lines are disconnected during fitting, the system must be bled. The fault codes in the control unit usually need to be cleared as well. |
| What do the codes 78RA on the housing mean? |
| They are markings of the module version. They help tell the units apart, but the full part number is what decides compatibility. |
| Is this a new part? |
| No. We sell used original modules, each one inspected before sale. You will find the warranty period in the product features table. |
Not sure about the match? Send us a photo of the numbers on your ABS pump and we will check whether this module will fit.
