A faulty transmission control module (TCM) most often causes limp mode with the gearbox stuck in one gear, harsh jolts when you select D or R, erratic gear changes, flashing PRND letters and a gearbox or engine warning light. However, the same symptoms are often caused by a low gearbox oil level, a weak battery, a poor earth or a faulty sensor. To test a transmission control module, start by checking the battery and reading the fault codes with a diagnostic tool that can talk to the gearbox control unit, then check the power supply, the connector, the oil and the live data. Below we explain the symptoms, the diagnostic steps and what the most common fault codes mean.
Engine Control Unit Volkswagen, Skoda 1.4 TDI Delphi DCM6.2V 04B907445 284312287
Vendors's code: 284312287
Product code: 97E2-825AC
Barcode:
Code 39:
ISBN:
Select a product option:
Individual variants may differ in price
product option
Important: Depending on the ECU type and vehicle model, not all of the options listed below may be available.
To select the correct option for your vehicle and ECU, please contact us before purchasing:
contact@auto24parts.com
1. Locked
This option is intended for professional workshops with the required specialist equipment and technical knowledge.
The ECU has been removed from a vehicle intended for recycling and still contains the immobilizer data and other information from the previous vehicle. Before it can be used in another car, it must be unlocked and then programmed using specialist automotive diagnostic equipment.
2. Unlocked
Several preparation methods may be available. The possible options depend on the ECU type, vehicle model and immobilizer system. Please contact us before purchasing, as some preparation methods are not available for every ECU.
Our electronics specialists can prepare the ECU in one of the following ways:
a) ECU with PIN code (Car Pass)
The PIN code is supplied, but programming with a suitable diagnostic tool is still required. After installing the ECU, it must be reset using the supplied PIN code and then programmed to the vehicle’s immobilizer system.
b) VIRGIN ECU
The data from the previous vehicle is removed and the ECU is restored to a clean, factory-like state. After installation, it must be programmed to the vehicle using a compatible specialist diagnostic tool. Unless another preparation method is specified in the product description, this is the standard unlocking option for most of our ECUs.
c) Plug & Play – IMMO OFF
The immobilizer function is disabled in the ECU. After installation, the engine can start without additional immobilizer programming. Please note that the vehicle will no longer have an active immobilizer function, and an immobilizer warning light or fault code may remain, depending on the vehicle model.
d) Plug & Play – Automatic Programming
After installation, the ECU automatically learns and saves the required vehicle data. No additional programming is normally required.
e) Plug & Play – 1:1 Clone
The data from your original ECU is copied to another fully functional ECU. The cloned unit is then ready for installation without additional programming.
You must send us your original ECU so that we can transfer its data to the replacement unit.
The original ECU must have working communication with the vehicle, a diagnostic tool or our programming equipment. If the required data cannot be read, a complete 1:1 clone may not be possible.
3. Complete Plug & Play Set
A complete matched set containing the ECU, immobilizer components and all other parts required to start the vehicle without additional programming. All components supplied in the set must be installed in the vehicle.
Important:
Dispatch time depends on the selected option. If an unlocked or specially prepared version is ordered, the preparation service usually requires an additional 1–2 business days.
Ask about the product
Administratorem danych osobowych jest Auto24parts. Przetwarzamy je w celu przesłania odpowiedzi na zapytanie. Więcej informacji dotyczących przetwarzania danych osobowych znajduje się w polityce prywatności.
Price 30 euros applies shipments to 5 kg on worldwide. Above this weight, please contact us by email to check price
Shipping cost for the selected product
The shipping cost applies to this product (in the selected variant - if applicable). It may change after adding other products to the cart.
How can I check whether ECU 04B907445 with Delphi number 284312287 fits my vehicle?
Compare two numbers on the label: VW 04B907445 and Delphi 284312287. We sell this used, working DCM6.2V module from a Volkswagen or Skoda 1.4 TDI locked or unlocked.
Engine Control Unit Volkswagen, Skoda 1.4 TDI Delphi DCM6.2V 04B907445 284312287
Volkswagen and Skoda models with the 1.4 TDI engine used Delphi ECUs from the DCM6.2V family. This unit has Volkswagen number 04B907445, which it shares with other versions, and Delphi number 284312287. The module controls fuel injection, turbo boost and starting of the diesel engine.
Numbers to compare
- 04B907445 – Volkswagen part number
- 284312287 – Delphi number read from this unit
- DCM6.2V – Delphi diesel ECU family
The VW number alone does not settle compatibility, as it contains no version letter. Before ordering, send us a photo of the label – we will compare the Delphi number and confirm whether the module matches yours.
Symptoms to look out for
- the engine will not start despite a working starter motor,
- a message about no communication with the module,
- limp mode and a clear loss of power,
- damage after a jump start or a voltage spike.
First check the battery, earth leads and the condition of the connector. If these are all in order and the symptoms persist, the module itself may be the cause.
Two ways to buy
The locked version is an ECU with the data and immobiliser of the donor vehicle – it is bought by workshops that will unlock, program and match it themselves. The unlocked version is prepared in-house before the parcel is dispatched, usually within 1–2 working days.
Not every method (PIN / CAR PASS, Virgin, IMMO OFF, auto programming, cloning) is possible for every ECU – it depends on the number, software and immobiliser. Please ask before you order. Details: ECU preparation options.
Questions and answers
| Why is the Delphi number so important? |
|---|
| Because different versions of the module share number 04B907445, and it is the Delphi number that tells them apart. |
| How long does it take to prepare the unlocked version? |
| Usually 1–2 working days before dispatch. |
| What condition is the module in? |
| Used, in working order and in good condition. You will find the warranty period in the product features table. |
Send a photo of the label to contact@auto24parts.com – we will confirm compatibility with 04B907445.