A faulty transmission control module (TCM) most often causes limp mode with the gearbox stuck in one gear, harsh jolts when you select D or R, erratic gear changes, flashing PRND letters and a gearbox or engine warning light. However, the same symptoms are often caused by a low gearbox oil level, a weak battery, a poor earth or a faulty sensor. To test a transmission control module, start by checking the battery and reading the fault codes with a diagnostic tool that can talk to the gearbox control unit, then check the power supply, the connector, the oil and the live data. Below we explain the symptoms, the diagnostic steps and what the most common fault codes mean.
Engine Control Unit Volkswagen T5 2.5 TDI Bosch 070906016BD 0281011835
Vendors's code: 0281011835
Product code: D0C4-49106
Barcode:
Code 39:
ISBN:
Select a product option:
Individual variants may differ in price
product option
Important: Depending on the ECU type and vehicle model, not all of the options listed below may be available.
To select the correct option for your vehicle and ECU, please contact us before purchasing:
contact@auto24parts.com
1. Locked
This option is intended for professional workshops with the required specialist equipment and technical knowledge.
The ECU has been removed from a vehicle intended for recycling and still contains the immobilizer data and other information from the previous vehicle. Before it can be used in another car, it must be unlocked and then programmed using specialist automotive diagnostic equipment.
2. Unlocked
Several preparation methods may be available. The possible options depend on the ECU type, vehicle model and immobilizer system. Please contact us before purchasing, as some preparation methods are not available for every ECU.
Our electronics specialists can prepare the ECU in one of the following ways:
a) ECU with PIN code (Car Pass)
The PIN code is supplied, but programming with a suitable diagnostic tool is still required. After installing the ECU, it must be reset using the supplied PIN code and then programmed to the vehicle’s immobilizer system.
b) VIRGIN ECU
The data from the previous vehicle is removed and the ECU is restored to a clean, factory-like state. After installation, it must be programmed to the vehicle using a compatible specialist diagnostic tool. Unless another preparation method is specified in the product description, this is the standard unlocking option for most of our ECUs.
c) Plug & Play – IMMO OFF
The immobilizer function is disabled in the ECU. After installation, the engine can start without additional immobilizer programming. Please note that the vehicle will no longer have an active immobilizer function, and an immobilizer warning light or fault code may remain, depending on the vehicle model.
d) Plug & Play – Automatic Programming
After installation, the ECU automatically learns and saves the required vehicle data. No additional programming is normally required.
e) Plug & Play – 1:1 Clone
The data from your original ECU is copied to another fully functional ECU. The cloned unit is then ready for installation without additional programming.
You must send us your original ECU so that we can transfer its data to the replacement unit.
The original ECU must have working communication with the vehicle, a diagnostic tool or our programming equipment. If the required data cannot be read, a complete 1:1 clone may not be possible.
3. Complete Plug & Play Set
A complete matched set containing the ECU, immobilizer components and all other parts required to start the vehicle without additional programming. All components supplied in the set must be installed in the vehicle.
Important:
Dispatch time depends on the selected option. If an unlocked or specially prepared version is ordered, the preparation service usually requires an additional 1–2 business days.
Ask about the product
Administratorem danych osobowych jest Auto24parts. Przetwarzamy je w celu przesłania odpowiedzi na zapytanie. Więcej informacji dotyczących przetwarzania danych osobowych znajduje się w polityce prywatności.
Price 30 euros applies shipments to 5 kg on worldwide. Above this weight, please contact us by email to check price
Shipping cost for the selected product
The shipping cost applies to this product (in the selected variant - if applicable). It may change after adding other products to the cart.
Does module 070906016BD fit a T5 with the 2.5 TDI engine?
Yes, if your current ECU has VW number 070906016BD and Bosch number 0281011835. This used, working unit comes from a Volkswagen T5 2.5 TDI.
Engine Control Unit Volkswagen T5 2.5 TDI Bosch 070906016BD 0281011835
The 2.5 TDI engine in the Volkswagen T5 needs an ECU that matches the software version. This Bosch module, number 0281011835, has VW part number 070906016BD. It handles fuel metering, monitors the running of the diesel engine and communicates with the vehicle's other modules. We offer it used, in working order and in good condition.
Numbers on the casing
- 070906016BD – VW part number
- 0281011835 – Bosch number (0 281 011 835 on the label)
The BD suffix identifies a specific ECU version. There are 070906016 modules with other letters for the T5 2.5 TDI, so always check the full number.
What to look out for – symptoms
- the T5 will not start even though the starter motor works,
- the engine warning light is on and the diagnostic tool cannot connect to the ECU,
- reduced power and limp mode,
- module damage after water ingress.
Before deciding to replace it, measure the supply voltage and check the earths and the connector. If these are all fine and the symptoms persist, a module failure becomes very likely.
How we supply the ECU
You have two options. The first is an unlocked ECU – prepared before dispatch, usually within 1–2 working days. The second is a locked ECU, with the data and immobiliser of the previous vehicle, intended for workshops that will unlock, program and match it themselves.
The preparation method (PIN / CAR PASS, Virgin, IMMO OFF, auto programming, cloning) depends on the number, software and immobiliser, so not every method is available. Please ask us before buying. Details: ECU preparation options.
Questions and answers
| Does it fit a T5 with an engine other than the 2.5 TDI? |
|---|
| This module comes from a T5 2.5 TDI. However, what always decides is a match with number 070906016BD. |
| What is needed after fitting the locked version? |
| Unlocking, programming and matching to the immobiliser. |
| What condition is the part in? |
| It is a used part, in working order and in good condition. You will find the warranty period in the product features table. |
We will check compatibility based on the numbers – email contact@auto24parts.com.