Skip to main content
English £
English £
Open search engine
Search
Close search engine Clear Search
Open search engine
Search
Close search engine Clear Search
English £
English £
Products in the cart: 0. See details
Open search engine
Search
Close search engine Clear Search

Airbag clock spring Opel Vectra C Signum 13132473 CK

  • Part Type Airbag clock spring
  • Vehicle Make and Model Opel Vectra C Signum
  • OEM Part Number 13132473 CK / 13132473CK
  • Condition Used part
with VAT without VAT
Price £22.75
Availability:
In stock
pcs.

Fast Delivery

DHL Express - 30 euro

6 Month Warranty

Returns Possible up to 14 days

Secure payments

Stripe - Paypal - Credit Card
Ask about the product
Shipping from £22.75 - shipping (Poland)

Price 30 euros applies shipments to 5 kg on worldwide. Above this weight, please contact us by email to check price


PRODUCT DETAILS

  • Part Type Airbag clock spring
  • Vehicle Make and Model Opel Vectra C Signum
  • OEM Part Number 13132473 CK / 13132473CK
  • Condition Used part

Does airbag clock spring 13132473 CK fit your Opel Vectra C?

We offer a used airbag clock spring 13132473 CK for the Opel Vectra C and Opel Signum. The number on the housing decides the fit, so check it before you order.

Go to full description

Airbag clock spring Opel Vectra C Signum 13132473 CK

We sell a used airbag clock spring with number 13132473 CK. According to the listing it fits the Opel Vectra C and Opel Signum. In the Vectra C and Signum the clock spring is part of the module under the steering wheel, and versions differ by the letter code next to the GM number.

Numbers on the label

  • 13132473 CK / 13132473CK - OEM number (GM)

Models in the listing

  • Opel Vectra C
  • Opel Signum

Inside the housing there is a conductive ribbon wound like a spring. It carries the signal to the driver airbag and from the wheel buttons while the wheel turns.

Typical fault symptoms

  • the airbag warning light comes on, often after turning the wheel,
  • the horn does not work,
  • the airbag module stores a driver airbag circuit fault.

Before fitting

Before work, disconnect the battery and wait the time specified by the car maker. Set the wheels straight and fit the clock spring in its centre position, using the marks on the housing. The clock spring is fitted with the wheels pointing straight ahead and in the centre position. If it is set wrongly, it can tear at the first full turn.

Customer questions

Will the airbag light go out after replacement?
If the clock spring was the cause, usually yes, but a stored fault sometimes has to be cleared with a diagnostic tool.
Does the clock spring need centring before fitting?
Yes. It is fitted in the centre position with the wheels pointing straight ahead.
Can I send a photo of my part?
Yes, send a photo of the label to contact@auto24parts.com and we will check the fit.

We are happy to help: contact@auto24parts.com. Include your car model and a photo of your clock spring.

  • How to Check the Operation of a Transmission Control Module - Symptoms

    A faulty transmission control module (TCM) most often causes limp mode with the gearbox stuck in one gear, harsh jolts when you select D or R, erratic gear changes, flashing PRND letters and a gearbox or engine warning light. However, the same symptoms are often caused by a low gearbox oil level, a weak battery, a poor earth or a faulty sensor. To test a transmission control module, start by checking the battery and reading the fault codes with a diagnostic tool that can talk to the gearbox control unit, then check the power supply, the connector, the oil and the live data. Below we explain the symptoms, the diagnostic steps and what the most common fault codes mean.

    Read more
  • Burned Engine Control Unit: Symptoms, Causes, and the Optimal Solution

    A burned engine control unit (ECU) usually causes a sudden no-start: the engine cranks but will not start, the diagnostic tool cannot connect to the ECU, and the engine management light does not come on when you switch on the ignition. The most common causes are a voltage spike when jump-starting, reversed battery polarity, a faulty voltage regulator and a short circuit in the wiring loom or in an actuator. Below we explain how to tell a burned ECU from a power supply fault, what causes this kind of failure and how to choose a replacement ECU.

    Read more
  • Flooded Automatic Transmission Control Module or Burnt TCM - Symptoms

    A burnt-out or flooded automatic transmission control module (TCM) usually causes sudden symptoms: limp mode with the gearbox stuck in one gear, harsh thumps when you select D or R, no response to the gear selector, flashing or blank PRND letters and no communication between the diagnostic tool and the gearbox control unit. Flooding is most often caused by blocked scuttle panel drains, washing the engine bay or coolant in the gearbox oil, and a burnout by overheating, a short circuit or a voltage spike. Below we explain the symptoms, what to do straight away and why drying out or repairing such a control unit rarely gives a lasting result.

    Read more
  • Flooded engine control unit - symptoms, consequences and what to do

    A flooded engine control unit (ECU) most often causes a no-start, a 'Christmas tree' of warning lights on the dashboard, no communication with the diagnostic tool, or rough running in limp mode. Water usually gets into the ECU from blocked scuttle drains, after the engine bay has been cleaned with a pressure washer, or after driving through deep water. Below we describe the symptoms of a water-damaged ECU, what to do straight after the ECU gets wet, and why drying or repairing it rarely gives lasting results.

    Read more