A properly functioning ABS system is the foundation of road safety. Its main task is to prevent wheel lock-up during emergency braking, which allows the driver to maintain full control of the vehicle. The heart of this system is the electronic ABS pump controller. When it fails, the system stops working. A proper diagnosis of the problem allows you to avoid unnecessary costs and quickly restore brake efficiency.
ECU Engine controller OPEL VECTRA 1.8 DELCO 16204839 BLBH
Vendors's code: D95002
Product code: 16204839GM
Barcode:
Code 39:
ISBN:
€81.30
Price
€81.30
Regular price:
€81.30
0%
€100.00
Price
€100.00
Regular price:
€100.00
0%
Select a product option:
Individual variants may differ in price
product option
Important: Depending on the ECU type and vehicle model, not all of the options listed below may be available.
To select the correct option for your vehicle and ECU, please contact us before purchasing:
contact@auto24parts.com
1. Locked
This option is intended for professional workshops with the required specialist equipment and technical knowledge.
The ECU has been removed from a vehicle intended for recycling and still contains the immobilizer data and other information from the previous vehicle. Before it can be used in another car, it must be unlocked and then programmed using specialist automotive diagnostic equipment.
2. Unlocked
Several preparation methods may be available. The possible options depend on the ECU type, vehicle model and immobilizer system. Please contact us before purchasing, as some preparation methods are not available for every ECU.
Our electronics specialists can prepare the ECU in one of the following ways:
a) ECU with PIN code (Car Pass)
The PIN code is supplied, but programming with a suitable diagnostic tool is still required. After installing the ECU, it must be reset using the supplied PIN code and then programmed to the vehicle’s immobilizer system.
b) VIRGIN ECU
The data from the previous vehicle is removed and the ECU is restored to a clean, factory-like state. After installation, it must be programmed to the vehicle using a compatible specialist diagnostic tool. Unless another preparation method is specified in the product description, this is the standard unlocking option for most of our ECUs.
c) Plug & Play – IMMO OFF
The immobilizer function is disabled in the ECU. After installation, the engine can start without additional immobilizer programming. Please note that the vehicle will no longer have an active immobilizer function, and an immobilizer warning light or fault code may remain, depending on the vehicle model.
d) Plug & Play – Automatic Programming
After installation, the ECU automatically learns and saves the required vehicle data. No additional programming is normally required.
e) Plug & Play – 1:1 Clone
The data from your original ECU is copied to another fully functional ECU. The cloned unit is then ready for installation without additional programming.
You must send us your original ECU so that we can transfer its data to the replacement unit.
The original ECU must have working communication with the vehicle, a diagnostic tool or our programming equipment. If the required data cannot be read, a complete 1:1 clone may not be possible.
3. Complete Plug & Play Set
A complete matched set containing the ECU, immobilizer components and all other parts required to start the vehicle without additional programming. All components supplied in the set must be installed in the vehicle.
Important:
Dispatch time depends on the selected option. If an unlocked or specially prepared version is ordered, the preparation service usually requires an additional 1–2 business days.
Ask about the product
ECU Engine controller OPEL VECTRA 1.8 DELCO 16204839 BLBH
Administratorem danych osobowych jest Auto24parts. Przetwarzamy je w celu przesłania odpowiedzi na zapytanie. Więcej informacji dotyczących przetwarzania danych osobowych znajduje się w polityce prywatności.
Shipping
from
€30.00
-
shipping
(Poland)
from
€30.00
-
shipping
(Poland)
Price 30 euros applies shipments to 5 kg on worldwide. Above this weight, please contact us by email to check price
Shipping cost for the selected product
The shipping cost applies to this product (in the selected variant - if applicable). It may change after adding other products to the cart.
ECU Engine controller OPEL VECTRA 1.8 16204839GM
Tested engine control unit for Opel Vectra 1.8 with part numbers 16204839GM and D95002, featuring warranty and fast shipping.
ECU Engine controller OPEL VECTRA 1.8 DELCO 16204839GM D95002 BLBH
Which Opel Vectra models are compatible with ECU 16204839GM?
The ECU Engine controller OPEL VECTRA 1.8 DELCO 16204839GM was used in Opel Vectra B models equipped with 1.8-liter petrol engines. This module is responsible for managing engine performance, ensuring optimal power delivery and smooth operation.
What is the function of the Opel ECU marked D95002?
The D95002 engine controller manages the fuel injection system and ignition timing. The computer analyzes sensor signals in real-time, resulting in stable idling and smooth throttle response in your vehicle.
What are the symptoms of a faulty BLBH module in Opel Vectra 1.8?
A damaged engine computer 16204839GM or a module with the BLBH code may result in starting issues, sudden stalling, or a check engine light. Every ECU unit we offer is technically verified before shipment.
Why is the part number 16204839GM important for replacement?
Verifying the 16204839GM number and D95002 code ensures a perfect match for your Opel's specific engine hardware. Using the identical part number guarantees full compatibility with the factory electrical harness.
Does the OPEL VECTRA 16204839GM engine controller require programming?
In most cases, the ECU Engine controller OPEL VECTRA 1.8 DELCO 16204839GM D95002 requires pairing with the vehicle's immobilizer system. Matching the part by BLBH numbers facilitates installation and correct operation.
