The automatic transmission control unit (often designated as TCU or TCM) is a crucial electronic component responsible for smooth and trouble-free gear shifting. Its failure, most often caused by overheating, short circuits, or water damage, results in jerking, an inability to shift gears, or the vehicle entering limp mode. Purchasing a new module at an authorized dealership is a massive expense, which is why replacing it with a fully functional, used original is the most reasonable solution.
ECU Engine Controller VOLKSWAGEN SKODA BOSCH 0261206758 06A906018GH
Vendors's code: 06A906018GH
Product code: 0261206758
Barcode:
Code 39:
ISBN:
€101.63
Price
€101.63
€125.00
Price
€125.00
Select a product option:
Individual variants may differ in price
product option
Important: Depending on the ECU type and vehicle model, not all of the options listed below may be available.
To select the correct option for your vehicle and ECU, please contact us before purchasing:
contact@auto24parts.com
1. Locked
This option is intended for professional workshops with the required specialist equipment and technical knowledge.
The ECU has been removed from a vehicle intended for recycling and still contains the immobilizer data and other information from the previous vehicle. Before it can be used in another car, it must be unlocked and then programmed using specialist automotive diagnostic equipment.
2. Unlocked
Several preparation methods may be available. The possible options depend on the ECU type, vehicle model and immobilizer system. Please contact us before purchasing, as some preparation methods are not available for every ECU.
Our electronics specialists can prepare the ECU in one of the following ways:
a) ECU with PIN code (Car Pass)
The PIN code is supplied, but programming with a suitable diagnostic tool is still required. After installing the ECU, it must be reset using the supplied PIN code and then programmed to the vehicle’s immobilizer system.
b) VIRGIN ECU
The data from the previous vehicle is removed and the ECU is restored to a clean, factory-like state. After installation, it must be programmed to the vehicle using a compatible specialist diagnostic tool. Unless another preparation method is specified in the product description, this is the standard unlocking option for most of our ECUs.
c) Plug & Play – IMMO OFF
The immobilizer function is disabled in the ECU. After installation, the engine can start without additional immobilizer programming. Please note that the vehicle will no longer have an active immobilizer function, and an immobilizer warning light or fault code may remain, depending on the vehicle model.
d) Plug & Play – Automatic Programming
After installation, the ECU automatically learns and saves the required vehicle data. No additional programming is normally required.
e) Plug & Play – 1:1 Clone
The data from your original ECU is copied to another fully functional ECU. The cloned unit is then ready for installation without additional programming.
You must send us your original ECU so that we can transfer its data to the replacement unit.
The original ECU must have working communication with the vehicle, a diagnostic tool or our programming equipment. If the required data cannot be read, a complete 1:1 clone may not be possible.
3. Complete Plug & Play Set
A complete matched set containing the ECU, immobilizer components and all other parts required to start the vehicle without additional programming. All components supplied in the set must be installed in the vehicle.
Important:
Dispatch time depends on the selected option. If an unlocked or specially prepared version is ordered, the preparation service usually requires an additional 1–2 business days.
Ask about the product
ECU Engine Controller VOLKSWAGEN SKODA BOSCH 0261206758 06A906018GH
Administratorem danych osobowych jest Auto24parts. Przetwarzamy je w celu przesłania odpowiedzi na zapytanie. Więcej informacji dotyczących przetwarzania danych osobowych znajduje się w polityce prywatności.
Shipping
from
€30.00
-
shipping
(Poland)
from
€30.00
-
shipping
(Poland)
Price 30 euros applies shipments to 5 kg on worldwide. Above this weight, please contact us by email to check price
Shipping cost for the selected product
The shipping cost applies to this product (in the selected variant - if applicable). It may change after adding other products to the cart.
ECU ENGINE CONTROLLER VOLKSWAGEN SKODA BOSCH 0261206758 06A906018GH
Tested Bosch engine controller for Volkswagen and Skoda with numbers 0261206758 and 06A906018GH, guaranteed and fast shipping directly to the customer.
ECU Engine Controller VOLKSWAGEN SKODA BOSCH 0261206758 06A906018GH
Which models are compatible with the engine controller 0261206758 06A906018GH?
This controller fits many Volkswagen and Skoda car models. With universal numbers 0261206758 and 06A906018GH, it is compatible with various engine versions.
What is the role of the engine controller 0261206758 06A906018GH?
The engine controller, also known as ECU, manages engine operation by controlling aspects like fuel injection and ignition. Numbers 0261206758 and 06A906018GH ensure proper compatibility with vehicle systems.
What are the symptoms of a faulty controller 0261206758 06A906018GH?
Common symptoms include rough engine operation, ignition issues, or increased fuel consumption. If your vehicle shows such signs, it's worth checking the controller with numbers 0261206758 and 06A906018GH.
Where can I find the number on the controller?
Numbers like 0261206758 and 06A906018GH are usually located on the controller's casing. They may be written with or without spaces, making them easy to identify.
Does the controller 0261206758 06A906018GH require programming after installation?
In most cases, the controller with numbers 0261206758 and 06A906018GH does not require additional programming after installation, simplifying its setup. Warranty and fast shipping are additional benefits.
