The automatic transmission control unit (often designated as TCU or TCM) is a crucial electronic component responsible for smooth and trouble-free gear shifting. Its failure, most often caused by overheating, short circuits, or water damage, results in jerking, an inability to shift gears, or the vehicle entering limp mode. Purchasing a new module at an authorized dealership is a massive expense, which is why replacing it with a fully functional, used original is the most reasonable solution.
ECU Engine controller VW Skoda Seat Bosch 0261203933 6K0906027D
Vendors's code: 6K0906027D
Product code: 0261203933
Barcode:
Code 39:
ISBN:
Select a product option:
Individual variants may differ in price
product option
Important: Depending on the ECU type and vehicle model, not all of the options listed below may be available.
To select the correct option for your vehicle and ECU, please contact us before purchasing:
contact@auto24parts.com
1. Locked
This option is intended for professional workshops with the required specialist equipment and technical knowledge.
The ECU has been removed from a vehicle intended for recycling and still contains the immobilizer data and other information from the previous vehicle. Before it can be used in another car, it must be unlocked and then programmed using specialist automotive diagnostic equipment.
2. Unlocked
Several preparation methods may be available. The possible options depend on the ECU type, vehicle model and immobilizer system. Please contact us before purchasing, as some preparation methods are not available for every ECU.
Our electronics specialists can prepare the ECU in one of the following ways:
a) ECU with PIN code (Car Pass)
The PIN code is supplied, but programming with a suitable diagnostic tool is still required. After installing the ECU, it must be reset using the supplied PIN code and then programmed to the vehicle’s immobilizer system.
b) VIRGIN ECU
The data from the previous vehicle is removed and the ECU is restored to a clean, factory-like state. After installation, it must be programmed to the vehicle using a compatible specialist diagnostic tool. Unless another preparation method is specified in the product description, this is the standard unlocking option for most of our ECUs.
c) Plug & Play – IMMO OFF
The immobilizer function is disabled in the ECU. After installation, the engine can start without additional immobilizer programming. Please note that the vehicle will no longer have an active immobilizer function, and an immobilizer warning light or fault code may remain, depending on the vehicle model.
d) Plug & Play – Automatic Programming
After installation, the ECU automatically learns and saves the required vehicle data. No additional programming is normally required.
e) Plug & Play – 1:1 Clone
The data from your original ECU is copied to another fully functional ECU. The cloned unit is then ready for installation without additional programming.
You must send us your original ECU so that we can transfer its data to the replacement unit.
The original ECU must have working communication with the vehicle, a diagnostic tool or our programming equipment. If the required data cannot be read, a complete 1:1 clone may not be possible.
3. Complete Plug & Play Set
A complete matched set containing the ECU, immobilizer components and all other parts required to start the vehicle without additional programming. All components supplied in the set must be installed in the vehicle.
Important:
Dispatch time depends on the selected option. If an unlocked or specially prepared version is ordered, the preparation service usually requires an additional 1–2 business days.
Ask about the product
ECU Engine controller VW Skoda Seat Bosch 0261203933 6K0906027D
Administratorem danych osobowych jest Auto24parts. Przetwarzamy je w celu przesłania odpowiedzi na zapytanie. Więcej informacji dotyczących przetwarzania danych osobowych znajduje się w polityce prywatności.
Shipping
from
€30.00
-
shipping
(Poland)
from
€30.00
-
shipping
(Poland)
Price 30 euros applies shipments to 5 kg on worldwide. Above this weight, please contact us by email to check price
Shipping cost for the selected product
The shipping cost applies to this product (in the selected variant - if applicable). It may change after adding other products to the cart.
Perfect choice for your VW, Skoda, or Seat
Looking for a reliable engine controller for your vehicle? Our Bosch product, with numbers 0261203933 and 6K0906027D, ensures quality and durability. Make sure the numbers match your original controller. We offer a 6-month warranty and fast shipping.
Why choose this engine controller?
The Bosch engine controller with numbers 0261203933 and 6K0906027D is an excellent choice for VW, Skoda, and Seat owners. This component is crucial for the proper functioning of the engine unit, so its quality is of utmost importance.
Before purchasing, we recommend checking the compatibility of the numbers. Proper matching of the controller is key to avoiding installation and vehicle operation issues. In some cases, programming or immobilizer matching may be required.
We provide a 6-month warranty, giving you peace of mind for trouble-free use. Our store also guarantees fast and secure shipping, so you can enjoy a fully functional car as soon as possible.
How to check number compatibility?
Compare the numbers on your old controller with 0261203933 and 6K0906027D. This is the key to proper matching.
Does this controller require programming?
In some cases, programming or immobilizer matching may be necessary. Consult with a mechanic.
Can I return the product if it doesn't fit?
Yes, we offer returns if the product is not compatible, provided it hasn't been used.
How quickly can I receive my order?
We ensure fast shipping, usually within 24 hours of purchase.
Does this controller fit all VW, Skoda, and Seat models?
It fits many models, but always check number compatibility to be sure.
