A faulty transmission control module (TCM) most often causes limp mode with the gearbox stuck in one gear, harsh jolts when you select D or R, erratic gear changes, flashing PRND letters and a gearbox or engine warning light. However, the same symptoms are often caused by a low gearbox oil level, a weak battery, a poor earth or a faulty sensor. To test a transmission control module, start by checking the battery and reading the fault codes with a diagnostic tool that can talk to the gearbox control unit, then check the power supply, the connector, the oil and the live data. Below we explain the symptoms, the diagnostic steps and what the most common fault codes mean.
Engine Control Unit Volkswagen T5 Bosch EDC16U1 070906016J 0281011266
Vendors's code: 0281011266
Product code: 0281011266
Barcode:
Code 39:
ISBN:
Select a product option:
Individual variants may differ in price
product option
Important: Depending on the ECU type and vehicle model, not all of the options listed below may be available.
To select the correct option for your vehicle and ECU, please contact us before purchasing:
contact@auto24parts.com
1. Locked
This option is intended for professional workshops with the required specialist equipment and technical knowledge.
The ECU has been removed from a vehicle intended for recycling and still contains the immobilizer data and other information from the previous vehicle. Before it can be used in another car, it must be unlocked and then programmed using specialist automotive diagnostic equipment.
2. Unlocked
Several preparation methods may be available. The possible options depend on the ECU type, vehicle model and immobilizer system. Please contact us before purchasing, as some preparation methods are not available for every ECU.
Our electronics specialists can prepare the ECU in one of the following ways:
a) ECU with PIN code (Car Pass)
The PIN code is supplied, but programming with a suitable diagnostic tool is still required. After installing the ECU, it must be reset using the supplied PIN code and then programmed to the vehicle’s immobilizer system.
b) VIRGIN ECU
The data from the previous vehicle is removed and the ECU is restored to a clean, factory-like state. After installation, it must be programmed to the vehicle using a compatible specialist diagnostic tool. Unless another preparation method is specified in the product description, this is the standard unlocking option for most of our ECUs.
c) Plug & Play – IMMO OFF
The immobilizer function is disabled in the ECU. After installation, the engine can start without additional immobilizer programming. Please note that the vehicle will no longer have an active immobilizer function, and an immobilizer warning light or fault code may remain, depending on the vehicle model.
d) Plug & Play – Automatic Programming
After installation, the ECU automatically learns and saves the required vehicle data. No additional programming is normally required.
e) Plug & Play – 1:1 Clone
The data from your original ECU is copied to another fully functional ECU. The cloned unit is then ready for installation without additional programming.
You must send us your original ECU so that we can transfer its data to the replacement unit.
The original ECU must have working communication with the vehicle, a diagnostic tool or our programming equipment. If the required data cannot be read, a complete 1:1 clone may not be possible.
3. Complete Plug & Play Set
A complete matched set containing the ECU, immobilizer components and all other parts required to start the vehicle without additional programming. All components supplied in the set must be installed in the vehicle.
Important:
Dispatch time depends on the selected option. If an unlocked or specially prepared version is ordered, the preparation service usually requires an additional 1–2 business days.
Ask about the product
Administratorem danych osobowych jest Auto24parts. Przetwarzamy je w celu przesłania odpowiedzi na zapytanie. Więcej informacji dotyczących przetwarzania danych osobowych znajduje się w polityce prywatności.
Price 30 euros applies shipments to 5 kg on worldwide. Above this weight, please contact us by email to check price
Shipping cost for the selected product
The shipping cost applies to this product (in the selected variant - if applicable). It may change after adding other products to the cart.
Where can I find number 070906016J on the ECU from a T5?
VW number 070906016J and Bosch number 0 281 011 266 are on the sticker on the casing. This used, working EDC16U1 ECU comes from a Volkswagen T5 – base your choice on the number.
Engine Control Unit Volkswagen T5 Bosch EDC16U1 070906016J 0281011266
The Bosch EDC16U1 ECU with number 070906016J comes from a Volkswagen T5. We do not state the engine size, so compatibility is decided by comparing the numbers on the label. Bosch number 0281011266, from the 0 281 series, indicates a diesel ECU that manages injection and the running of the engine. The module is used, in working order and in good condition.
Numbers on the sticker
- 070906016J – Volkswagen part number
- 0281011266 – Bosch number; on the label 0 281 011 266
- EDC16U1 – Bosch ECU type
The letter J at the end of the VW number denotes the software and hardware version. Check that your module shows exactly the same marking.
Symptoms pointing to the ECU
- no start with a good battery,
- the diagnostic computer cannot read the ECU,
- limp mode appearing with no sensor faults,
- damage after a voltage spike in the electrical system.
It is worth starting by checking the power supply and earth – this rules out the most common false alarms. Also inspect the connector pins, as green corrosion on the contacts can cut communication with the module.
Locked or unlocked
This EDC16U1 is available in two options. The unlocked unit is prepared before dispatch (usually 1–2 working days). The locked unit keeps the data and immobiliser from the donor vehicle, so we recommend it for workshops that will carry out the unlocking, programming and matching themselves.
Whether PIN / CAR PASS, Virgin, IMMO OFF, auto programming or cloning is possible depends on the number, software and immobiliser. Please ask before buying, and also read the description of the ECU preparation options.
Questions and answers
| Which T5 engine does this ECU fit? |
|---|
| We do not state the engine size. Compare number 070906016J with the label on your module. |
| What details should I send before buying? |
| All the numbers on the sticker of your current ECU, or a photo of it. |
| What condition is the ECU in? |
| It is a used part, in working order and in good condition. You will find the warranty period in the product features table. |
Email contact@auto24parts.com and we will check whether this module fits your T5.