A faulty transmission control module (TCM) most often causes limp mode with the gearbox stuck in one gear, harsh jolts when you select D or R, erratic gear changes, flashing PRND letters and a gearbox or engine warning light. However, the same symptoms are often caused by a low gearbox oil level, a weak battery, a poor earth or a faulty sensor. To test a transmission control module, start by checking the battery and reading the fault codes with a diagnostic tool that can talk to the gearbox control unit, then check the power supply, the connector, the oil and the live data. Below we explain the symptoms, the diagnostic steps and what the most common fault codes mean.
Engine Control Unit Volkswagen T5 3.2 Bosch 022906032JB 0261201268
Vendors's code: 0261201268
Product code: 0261201268
Barcode:
Code 39:
ISBN:
Select a product option:
Individual variants may differ in price
product option
Important: Depending on the ECU type and vehicle model, not all of the options listed below may be available.
To select the correct option for your vehicle and ECU, please contact us before purchasing:
contact@auto24parts.com
1. Locked
This option is intended for professional workshops with the required specialist equipment and technical knowledge.
The ECU has been removed from a vehicle intended for recycling and still contains the immobilizer data and other information from the previous vehicle. Before it can be used in another car, it must be unlocked and then programmed using specialist automotive diagnostic equipment.
2. Unlocked
Several preparation methods may be available. The possible options depend on the ECU type, vehicle model and immobilizer system. Please contact us before purchasing, as some preparation methods are not available for every ECU.
Our electronics specialists can prepare the ECU in one of the following ways:
a) ECU with PIN code (Car Pass)
The PIN code is supplied, but programming with a suitable diagnostic tool is still required. After installing the ECU, it must be reset using the supplied PIN code and then programmed to the vehicle’s immobilizer system.
b) VIRGIN ECU
The data from the previous vehicle is removed and the ECU is restored to a clean, factory-like state. After installation, it must be programmed to the vehicle using a compatible specialist diagnostic tool. Unless another preparation method is specified in the product description, this is the standard unlocking option for most of our ECUs.
c) Plug & Play – IMMO OFF
The immobilizer function is disabled in the ECU. After installation, the engine can start without additional immobilizer programming. Please note that the vehicle will no longer have an active immobilizer function, and an immobilizer warning light or fault code may remain, depending on the vehicle model.
d) Plug & Play – Automatic Programming
After installation, the ECU automatically learns and saves the required vehicle data. No additional programming is normally required.
e) Plug & Play – 1:1 Clone
The data from your original ECU is copied to another fully functional ECU. The cloned unit is then ready for installation without additional programming.
You must send us your original ECU so that we can transfer its data to the replacement unit.
The original ECU must have working communication with the vehicle, a diagnostic tool or our programming equipment. If the required data cannot be read, a complete 1:1 clone may not be possible.
3. Complete Plug & Play Set
A complete matched set containing the ECU, immobilizer components and all other parts required to start the vehicle without additional programming. All components supplied in the set must be installed in the vehicle.
Important:
Dispatch time depends on the selected option. If an unlocked or specially prepared version is ordered, the preparation service usually requires an additional 1–2 business days.
Ask about the product
Administratorem danych osobowych jest Auto24parts. Przetwarzamy je w celu przesłania odpowiedzi na zapytanie. Więcej informacji dotyczących przetwarzania danych osobowych znajduje się w polityce prywatności.
Price 30 euros applies shipments to 5 kg on worldwide. Above this weight, please contact us by email to check price
Shipping cost for the selected product
The shipping cost applies to this product (in the selected variant - if applicable). It may change after adding other products to the cart.
What does the JB suffix in 022906032JB mean?
The letters JB identify a specific version of the Bosch engine control unit for the Volkswagen T5 3.2 petrol – different from, say, GM. The unit is used, in working order and carries Bosch number 0 261 201 268.
Engine Control Unit Volkswagen T5 3.2 Bosch 022906032JB 0261201268
With ECUs for the T5 3.2, the suffix of the VW number is what you need to check most carefully. This Bosch unit is numbered 022906032JB, and its manufacturer number is 0261201268. It manages the 3.2 petrol engine: it sets fuel quantity and ignition timing, controls idle speed and responds to sensor signals. The data does not give the ECU family, so compatibility comes down to the numbers.
Numbers on the unit's label
- 022906032JB – Volkswagen part number
- 0261201268 – Bosch number; shown on the label as 0 261 201 268
The 0 261 prefix is Bosch's numbering for petrol engine ECUs. Versions of 022906032 differ by suffix, and each may run different software – so a replacement should carry the letters JB.
Signs the ECU may be faulty
- the engine won't start even though injection and ignition are electrically sound,
- misfires despite good coils and spark plugs,
- engine warning light and no response to the throttle,
- no connection to the unit during diagnostics.
Start by checking the supply voltage at the connector and the earths – many “ECU failures” turn out to be wiring loom problems.
How we supply this ECU
There are two options. A locked unit holds the data and immobiliser of the vehicle it was removed from – it is bought by workshops that unlock, program and match ECUs themselves. An unlocked unit is prepared in-house before dispatch, usually within 1–2 working days.
Not every unlocking method is possible for every ECU: PIN / CAR PASS, Virgin, IMMO OFF, auto programming or cloning depend on the part number, software and immobiliser. Please ask before buying. All options are described here: ECU preparation options.
Questions and answers
| Are 022906032JB and 022906032GM interchangeable? |
|---|
| Don't assume so. They are different versions – send us your ECU number and we'll check compatibility. |
| Where can I find the Bosch number? |
| On the same label as the VW number, usually in the format 0 261 201 268. |
| What details should I send before buying the unlocked version? |
| All the numbers from the label of your current unit, or a clear photo of it. |
| What condition is the ECU in? |
| It is a used part, in working order and in good condition. You will find the warranty period in the product features table. |
Email contact@auto24parts.com – we'll help you choose the right version.