The automatic transmission control unit (often designated as TCU or TCM) is a crucial electronic component responsible for smooth and trouble-free gear shifting. Its failure, most often caused by overheating, short circuits, or water damage, results in jerking, an inability to shift gears, or the vehicle entering limp mode. Purchasing a new module at an authorized dealership is a massive expense, which is why replacing it with a fully functional, used original is the most reasonable solution.
ECU Engine controller FORD TRANSIT 6C11-12A650-CG 4CFG
Vendors's code: 6C1112A650CG
Product code: 4CFG
Barcode:
Code 39:
ISBN:
Select a product option:
Individual variants may differ in price
product option
Important: Depending on the ECU type and vehicle model, not all of the options listed below may be available.
To select the correct option for your vehicle and ECU, please contact us before purchasing:
contact@auto24parts.com
1. Locked
This option is intended for professional workshops with the required specialist equipment and technical knowledge.
The ECU has been removed from a vehicle intended for recycling and still contains the immobilizer data and other information from the previous vehicle. Before it can be used in another car, it must be unlocked and then programmed using specialist automotive diagnostic equipment.
2. Unlocked
Several preparation methods may be available. The possible options depend on the ECU type, vehicle model and immobilizer system. Please contact us before purchasing, as some preparation methods are not available for every ECU.
Our electronics specialists can prepare the ECU in one of the following ways:
a) ECU with PIN code (Car Pass)
The PIN code is supplied, but programming with a suitable diagnostic tool is still required. After installing the ECU, it must be reset using the supplied PIN code and then programmed to the vehicle’s immobilizer system.
b) VIRGIN ECU
The data from the previous vehicle is removed and the ECU is restored to a clean, factory-like state. After installation, it must be programmed to the vehicle using a compatible specialist diagnostic tool. Unless another preparation method is specified in the product description, this is the standard unlocking option for most of our ECUs.
c) Plug & Play – IMMO OFF
The immobilizer function is disabled in the ECU. After installation, the engine can start without additional immobilizer programming. Please note that the vehicle will no longer have an active immobilizer function, and an immobilizer warning light or fault code may remain, depending on the vehicle model.
d) Plug & Play – Automatic Programming
After installation, the ECU automatically learns and saves the required vehicle data. No additional programming is normally required.
e) Plug & Play – 1:1 Clone
The data from your original ECU is copied to another fully functional ECU. The cloned unit is then ready for installation without additional programming.
You must send us your original ECU so that we can transfer its data to the replacement unit.
The original ECU must have working communication with the vehicle, a diagnostic tool or our programming equipment. If the required data cannot be read, a complete 1:1 clone may not be possible.
3. Complete Plug & Play Set
A complete matched set containing the ECU, immobilizer components and all other parts required to start the vehicle without additional programming. All components supplied in the set must be installed in the vehicle.
Important:
Dispatch time depends on the selected option. If an unlocked or specially prepared version is ordered, the preparation service usually requires an additional 1–2 business days.
Ask about the product
Administratorem danych osobowych jest Auto24parts. Przetwarzamy je w celu przesłania odpowiedzi na zapytanie. Więcej informacji dotyczących przetwarzania danych osobowych znajduje się w polityce prywatności.
Price 30 euros applies shipments to 5 kg on worldwide. Above this weight, please contact us by email to check price
Shipping cost for the selected product
The shipping cost applies to this product (in the selected variant - if applicable). It may change after adding other products to the cart.
FORD TRANSIT 4CFG – Engine ECU 6C11-12A650-CG
Original engine ECU for Ford Transit, part number 6C11-12A650-CG and code 4CFG, tested before sale.
FAQ – Ford Transit 6C11-12A650-CG 4CFG Engine ECU
1. Which vehicle is the 6C11-12A650-CG engine ECU designed for?
The 6C11-12A650-CG engine ECU is used in Ford Transit vehicles. Before purchasing, we recommend comparing the references on your original unit, as matching the correct part numbers is one of the most important factors when selecting a replacement ECU.
2. Will the Ford Transit 4CFG ECU replace my original unit?
If your original ECU is marked 4CFG and carries the part number 6C11-12A650-CG, this unit may be the correct replacement. If you are unsure, please send us a clear photo of the label on your original ECU before ordering so that the identification numbers can be checked.
3. Are 6C1112A650CG and 6C11-12A650-CG the same part number?
Yes. 6C1112A650CG is simply the same reference written without hyphens, while 6C11-12A650-CG is the standard formatted version. Both forms may appear when searching for a Ford Transit engine ECU.
4. Does the Ford Transit 6C11 12A650 CG ECU require programming?
The installation and start-up procedure depends on the configuration selected. The ECU may require appropriate preparation or adaptation to the vehicle and its immobiliser system. Before ordering, it is advisable to confirm how the Ford Transit 6C11 12A650 CG ECU should be prepared.
5. How can I make sure the 4CFG 6C11-12A650-CG ECU is correct for my vehicle?
The safest method is to compare the complete reference on your original engine ECU. Pay particular attention to 6C11-12A650-CG and 4CFG. If you are unsure whether this ECU is suitable for your Ford Transit, send us a photo of the original unit's label and we will help you check compatibility before purchase.