A faulty transmission control module (TCM) most often causes limp mode with the gearbox stuck in one gear, harsh jolts when you select D or R, erratic gear changes, flashing PRND letters and a gearbox or engine warning light. However, the same symptoms are often caused by a low gearbox oil level, a weak battery, a poor earth or a faulty sensor. To test a transmission control module, start by checking the battery and reading the fault codes with a diagnostic tool that can talk to the gearbox control unit, then check the power supply, the connector, the oil and the live data. Below we explain the symptoms, the diagnostic steps and what the most common fault codes mean.
Engine Control Unit Volkswagen Crafter Bosch 03L906012F 0281017666
Vendors's code: 0281017666
Product code: 63CF-91871
Barcode:
Code 39:
ISBN:
2 276,42 zł
Price
2 276,42 zł
2 800,00 zł
Price
2 800,00 zł
In stock
Select a product option:
Individual variants may differ in price
product option
Important: Depending on the ECU type and vehicle model, not all of the options listed below may be available.
To select the correct option for your vehicle and ECU, please contact us before purchasing:
contact@auto24parts.com
1. Locked
This option is intended for professional workshops with the required specialist equipment and technical knowledge.
The ECU has been removed from a vehicle intended for recycling and still contains the immobilizer data and other information from the previous vehicle. Before it can be used in another car, it must be unlocked and then programmed using specialist automotive diagnostic equipment.
2. Unlocked
Several preparation methods may be available. The possible options depend on the ECU type, vehicle model and immobilizer system. Please contact us before purchasing, as some preparation methods are not available for every ECU.
Our electronics specialists can prepare the ECU in one of the following ways:
a) ECU with PIN code (Car Pass)
The PIN code is supplied, but programming with a suitable diagnostic tool is still required. After installing the ECU, it must be reset using the supplied PIN code and then programmed to the vehicle’s immobilizer system.
b) VIRGIN ECU
The data from the previous vehicle is removed and the ECU is restored to a clean, factory-like state. After installation, it must be programmed to the vehicle using a compatible specialist diagnostic tool. Unless another preparation method is specified in the product description, this is the standard unlocking option for most of our ECUs.
c) Plug & Play – IMMO OFF
The immobilizer function is disabled in the ECU. After installation, the engine can start without additional immobilizer programming. Please note that the vehicle will no longer have an active immobilizer function, and an immobilizer warning light or fault code may remain, depending on the vehicle model.
d) Plug & Play – Automatic Programming
After installation, the ECU automatically learns and saves the required vehicle data. No additional programming is normally required.
e) Plug & Play – 1:1 Clone
The data from your original ECU is copied to another fully functional ECU. The cloned unit is then ready for installation without additional programming.
You must send us your original ECU so that we can transfer its data to the replacement unit.
The original ECU must have working communication with the vehicle, a diagnostic tool or our programming equipment. If the required data cannot be read, a complete 1:1 clone may not be possible.
3. Complete Plug & Play Set
A complete matched set containing the ECU, immobilizer components and all other parts required to start the vehicle without additional programming. All components supplied in the set must be installed in the vehicle.
Important:
Dispatch time depends on the selected option. If an unlocked or specially prepared version is ordered, the preparation service usually requires an additional 1–2 business days.
Ask about the product
Engine Control Unit Volkswagen Crafter Bosch 03L906012F 0281017666
Administratorem danych osobowych jest Auto24parts. Przetwarzamy je w celu przesłania odpowiedzi na zapytanie. Więcej informacji dotyczących przetwarzania danych osobowych znajduje się w polityce prywatności.
Shipping
from
120,00 zł
-
shipping
(Poland)
from
120,00 zł
-
shipping
(Poland)
Price 30 euros applies shipments to 5 kg on worldwide. Above this weight, please contact us by email to check price
Shipping cost for the selected product
The shipping cost applies to this product (in the selected variant - if applicable). It may change after adding other products to the cart.
Looking for a 03L906012F ECU for a Crafter?
We offer a used, working Bosch module with VW number 03L906012F and Bosch number 0281017666 (label: 0 281 017 666), listed as an ECU for the Volkswagen Crafter. Choose the locked or unlocked version.
Engine Control Unit Volkswagen Crafter Bosch 03L906012F 0281017666
We offer this ECU as a part for the Volkswagen Crafter, but when buying, the numbers are what matter most: VW 03L906012F and Bosch 0 281 017 666. The 0 281 prefix indicates a diesel engine ECU. The module oversees fuel injection and the sensors; we do not state the engine size in this listing.
Numbers to compare
- 03L906012F – VW number from the sticker on the casing
- 0281017666 – Bosch number (on the label: 0 281 017 666)
The letter F at the end of the VW number defines the software or hardware version. If your ECU has the number 03L906012 with a different letter, write to us before ordering.
Symptoms of a faulty engine control unit
- a flashing glow plug warning light combined with starting problems,
- software cannot be read or written via the diagnostic port,
- the engine cutting out or jerking while driving even though the ancillaries are working,
- intermittent communication with the immobiliser despite a correct key.
Before deciding to replace it, check the fuses, earths and ECU power supply – a damaged wiring loom produces similar symptoms.
Locked or unlocked version?
You can order this ECU in one of two versions. A locked ECU still holds the data and immobiliser of the previous car – it is the choice for workshops that will unlock, program and adapt it themselves. The unlocked version is prepared in-house before dispatch – usually within 1–2 working days.
The preparation method depends on the individual unit: the number, software and the immobiliser in the car. PIN code / CAR PASS, Virgin, IMMO OFF, auto programming or clone are not always available – ask before you buy. We explain how we prepare ECUs on the ECU preparation options page.
Questions and answers
| How long does it take to prepare the unlocked version? |
|---|
| Usually 1–2 working days, after which we dispatch the ECU. |
| Are 0281017666 and 03L906012F the same ECU? |
| Yes, they are two numbers of one module: 03L906012F was assigned by Volkswagen, and 0281017666 by Bosch. |
| Will the 03L906012F ECU start the engine immediately after fitting? |
| Not the locked version – it has to be programmed and adapted to the immobiliser. With the unlocked version, it depends on the preparation method, which we agree before purchase. |
| What condition is this ECU in? |
| It is a used part, working and in good condition. You will find the warranty period in the product features table. |
We are happy to help you choose a version – just send a message to contact@auto24parts.com with the numbers from the label.
