A faulty transmission control module (TCM) most often causes limp mode with the gearbox stuck in one gear, harsh jolts when you select D or R, erratic gear changes, flashing PRND letters and a gearbox or engine warning light. However, the same symptoms are often caused by a low gearbox oil level, a weak battery, a poor earth or a faulty sensor. To test a transmission control module, start by checking the battery and reading the fault codes with a diagnostic tool that can talk to the gearbox control unit, then check the power supply, the connector, the oil and the live data. Below we explain the symptoms, the diagnostic steps and what the most common fault codes mean.
Engine Control Unit Volkswagen Polo 1.2 TDI Delphi 03P906021F 28281669
Vendors's code: 28281669
Product code: 28281669
Barcode:
Code 39:
ISBN:
Select a product option:
Individual variants may differ in price
product option
Important: Depending on the ECU type and vehicle model, not all of the options listed below may be available.
To select the correct option for your vehicle and ECU, please contact us before purchasing:
contact@auto24parts.com
1. Locked
This option is intended for professional workshops with the required specialist equipment and technical knowledge.
The ECU has been removed from a vehicle intended for recycling and still contains the immobilizer data and other information from the previous vehicle. Before it can be used in another car, it must be unlocked and then programmed using specialist automotive diagnostic equipment.
2. Unlocked
Several preparation methods may be available. The possible options depend on the ECU type, vehicle model and immobilizer system. Please contact us before purchasing, as some preparation methods are not available for every ECU.
Our electronics specialists can prepare the ECU in one of the following ways:
a) ECU with PIN code (Car Pass)
The PIN code is supplied, but programming with a suitable diagnostic tool is still required. After installing the ECU, it must be reset using the supplied PIN code and then programmed to the vehicle’s immobilizer system.
b) VIRGIN ECU
The data from the previous vehicle is removed and the ECU is restored to a clean, factory-like state. After installation, it must be programmed to the vehicle using a compatible specialist diagnostic tool. Unless another preparation method is specified in the product description, this is the standard unlocking option for most of our ECUs.
c) Plug & Play – IMMO OFF
The immobilizer function is disabled in the ECU. After installation, the engine can start without additional immobilizer programming. Please note that the vehicle will no longer have an active immobilizer function, and an immobilizer warning light or fault code may remain, depending on the vehicle model.
d) Plug & Play – Automatic Programming
After installation, the ECU automatically learns and saves the required vehicle data. No additional programming is normally required.
e) Plug & Play – 1:1 Clone
The data from your original ECU is copied to another fully functional ECU. The cloned unit is then ready for installation without additional programming.
You must send us your original ECU so that we can transfer its data to the replacement unit.
The original ECU must have working communication with the vehicle, a diagnostic tool or our programming equipment. If the required data cannot be read, a complete 1:1 clone may not be possible.
3. Complete Plug & Play Set
A complete matched set containing the ECU, immobilizer components and all other parts required to start the vehicle without additional programming. All components supplied in the set must be installed in the vehicle.
Important:
Dispatch time depends on the selected option. If an unlocked or specially prepared version is ordered, the preparation service usually requires an additional 1–2 business days.
Ask about the product
Administratorem danych osobowych jest Auto24parts. Przetwarzamy je w celu przesłania odpowiedzi na zapytanie. Więcej informacji dotyczących przetwarzania danych osobowych znajduje się w polityce prywatności.
Price 30 euros applies shipments to 5 kg on worldwide. Above this weight, please contact us by email to check price
Shipping cost for the selected product
The shipping cost applies to this product (in the selected variant - if applicable). It may change after adding other products to the cart.
Will the 03P906021F ECU fit your Polo 1.2 TDI?
It will if the module from your car has VW number 03P906021F and Delphi number 28281669. This unit comes from a 2010 Polo 1.2 TDI.
Engine Control Unit Volkswagen Polo 1.2 TDI Delphi 03P906021F 28281669
This Delphi engine ECU comes from a 2010 Volkswagen Polo 1.2 TDI. It has VW number 03P906021F and Delphi number 28281669. The module calculates the fuel quantity and controls injection and boost. If it stops working, the Polo usually will not start or goes into limp mode, and the diagnostic tool often cannot connect to it at all. The car's year of manufacture is a useful guide, but the number on the label always decides the match.
How to identify this ECU
- 03P906021F – Volkswagen part number with suffix F
- 28281669 – Delphi number
The final letter F defines the software or hardware version. 03P906021 ECUs come with various letters, so when matching compare the full VW number and the Delphi number.
Fault symptoms
- no start despite a working power and fuel supply,
- reduced power with no sensor fault,
- no communication with the engine module,
- a fault after moisture or a voltage spike.
First check the fuses, power supply and earths, as well as the ECU connector. Also read the fault memory – the fault codes will help you distinguish a module failure from a faulty sensor or a damaged wire in the loom.
Options: locked and unlocked
The locked version contains the data and immobiliser of the donor car – the choice of workshops that unlock, program and adapt ECUs themselves. We prepare the unlocked version before dispatch, usually within 1–2 working days.
Whether PIN / CAR PASS, Virgin, IMMO OFF, auto programming or clone will be possible depends on the part number, software and immobiliser. Ask before you buy and see the description of engine control unit options.
Questions and answers
| Will 03P906021F replace a 03P906021B ECU? |
|---|
| Do not assume so – it is a different version. Send us a photo of the label and we will compare. |
| Is 28281669 the Delphi number? |
| Yes, it is the manufacturer's number of the same ECU. |
| What condition is this ECU in? |
| It is a used, fully working part in good condition. You will find the warranty period in the product features table. |
Questions about matching? Email contact@auto24parts.com.