A faulty transmission control module (TCM) most often causes limp mode with the gearbox stuck in one gear, harsh jolts when you select D or R, erratic gear changes, flashing PRND letters and a gearbox or engine warning light. However, the same symptoms are often caused by a low gearbox oil level, a weak battery, a poor earth or a faulty sensor. To test a transmission control module, start by checking the battery and reading the fault codes with a diagnostic tool that can talk to the gearbox control unit, then check the power supply, the connector, the oil and the live data. Below we explain the symptoms, the diagnostic steps and what the most common fault codes mean.
Engine Control Unit Volkswagen Polo 6R 1.2 TDI Delphi 03P906021B 28291398
Vendors's code: 28291398
Product code: 28291398
Barcode:
Code 39:
ISBN:
Select a product option:
Individual variants may differ in price
product option
Important: Depending on the ECU type and vehicle model, not all of the options listed below may be available.
To select the correct option for your vehicle and ECU, please contact us before purchasing:
contact@auto24parts.com
1. Locked
This option is intended for professional workshops with the required specialist equipment and technical knowledge.
The ECU has been removed from a vehicle intended for recycling and still contains the immobilizer data and other information from the previous vehicle. Before it can be used in another car, it must be unlocked and then programmed using specialist automotive diagnostic equipment.
2. Unlocked
Several preparation methods may be available. The possible options depend on the ECU type, vehicle model and immobilizer system. Please contact us before purchasing, as some preparation methods are not available for every ECU.
Our electronics specialists can prepare the ECU in one of the following ways:
a) ECU with PIN code (Car Pass)
The PIN code is supplied, but programming with a suitable diagnostic tool is still required. After installing the ECU, it must be reset using the supplied PIN code and then programmed to the vehicle’s immobilizer system.
b) VIRGIN ECU
The data from the previous vehicle is removed and the ECU is restored to a clean, factory-like state. After installation, it must be programmed to the vehicle using a compatible specialist diagnostic tool. Unless another preparation method is specified in the product description, this is the standard unlocking option for most of our ECUs.
c) Plug & Play – IMMO OFF
The immobilizer function is disabled in the ECU. After installation, the engine can start without additional immobilizer programming. Please note that the vehicle will no longer have an active immobilizer function, and an immobilizer warning light or fault code may remain, depending on the vehicle model.
d) Plug & Play – Automatic Programming
After installation, the ECU automatically learns and saves the required vehicle data. No additional programming is normally required.
e) Plug & Play – 1:1 Clone
The data from your original ECU is copied to another fully functional ECU. The cloned unit is then ready for installation without additional programming.
You must send us your original ECU so that we can transfer its data to the replacement unit.
The original ECU must have working communication with the vehicle, a diagnostic tool or our programming equipment. If the required data cannot be read, a complete 1:1 clone may not be possible.
3. Complete Plug & Play Set
A complete matched set containing the ECU, immobilizer components and all other parts required to start the vehicle without additional programming. All components supplied in the set must be installed in the vehicle.
Important:
Dispatch time depends on the selected option. If an unlocked or specially prepared version is ordered, the preparation service usually requires an additional 1–2 business days.
Ask about the product
Administratorem danych osobowych jest Auto24parts. Przetwarzamy je w celu przesłania odpowiedzi na zapytanie. Więcej informacji dotyczących przetwarzania danych osobowych znajduje się w polityce prywatności.
Price 30 euros applies shipments to 5 kg on worldwide. Above this weight, please contact us by email to check price
Shipping cost for the selected product
The shipping cost applies to this product (in the selected variant - if applicable). It may change after adding other products to the cart.
How does the 03P906021B ECU with Delphi number 28291398 differ from other 03P906021B units?
By its Delphi number: this module from a 2010 Polo 6R 1.2 TDI has 28291398. With the same VW number, the Delphi number lets you tell the units apart, so compare it with your label.
Engine Control Unit Volkswagen Polo 6R 1.2 TDI Delphi 03P906021B 28291398
Delphi number 28291398 is the key distinguishing feature of this ECU from a 2010 Volkswagen Polo 6R 1.2 TDI. VW number 03P906021B also appears on other units that have different Delphi numbers. The module manages fuel injection and boost on the diesel engine.
How to tell this module apart
- 28291398 – Delphi number – distinguishes this unit
- 03P906021B – Volkswagen part number with the letter B
The letter B in the VW number indicates the software or hardware version, but with this number it is worth also comparing the Delphi number. When both match, you can be sure it is the same type of module.
When to suspect the ECU
- the engine will not run although the fuel supply and starter are fine,
- warning light on and loss of power,
- the diagnostic tool cannot see the engine module,
- problems after moisture got into the wiring.
Before ordering, check the fuses, power supply and earths. If after these checks the module still does not respond to the diagnostic tool, the cause is most likely the ECU itself rather than the car's wiring.
How we prepare 28291398
We can send the ECU unlocked – prepared before dispatch, usually within 1–2 working days. We can also send it locked, with the data and immobiliser from the previous Polo; this version is chosen by workshops that unlock, program and adapt ECUs themselves.
PIN / CAR PASS, Virgin, IMMO OFF, auto programming or clone – which method will work depends on the part number, software and immobiliser. Ask before you buy and see the ECU options page.
Questions and answers
| I have a 03P906021B but a different Delphi number – what should I do? |
|---|
| Send us a photo of the label. We will check whether this ECU can replace yours. |
| Does this module come from a Polo 6R? |
| Yes, from a 2010 Polo 6R 1.2 TDI. |
| What condition is this ECU in? |
| It is a used, fully working part in good condition. You will find the warranty period in the product features table. |
Email contact@auto24parts.com – we will compare your ECU's numbers with this module.