Rover ABS Pumps and Control Modules

Rover ABS Pump – Complete Hydraulic Unit with ABS Controller

A Rover ABS pump is part of the anti-lock braking system responsible for controlling hydraulic brake pressure when wheel lock is detected. Depending on the system, the complete assembly can combine the hydraulic block, electric pump motor, solenoid valves and electronic ABS control module.

Auto24Parts offers original used Rover ABS assemblies identified primarily by their complete Bosch and vehicle-specific part numbers. In the current catalogue, important applications include Rover 25 and Rover 75.

How to choose the correct Rover ABS pump

The safest way to select a replacement is to compare the numbers printed or engraved on the original unit.

Check:

• the complete Bosch ABS pump number,
• the electronic ABS control-unit number,
• the Rover or supplier reference where present,
• all final digits and suffixes,
• vehicle model and engine version as supporting information.

Similar housings and identical connectors do not automatically mean that two ABS units are interchangeable.

Rover 25 – Bosch 0265216684 / SRB101210 / 0273004397

One of the units available in the catalogue is the Rover 25 ABS assembly Bosch 0265216684 / SRB101210 / 0273004397.

The important references are:

• Bosch 0 265 216 684,
• 0265216684,
• SRB101210,
• 0 273 004 397,
• 0273004397.

The product is catalogued for Rover 25 from the 1999–2005 period. Compatibility with a specific vehicle should still be confirmed using the numbers on the original ABS assembly.

Rover 75 – Bosch 0265222001 / 0265800001

For selected Rover 75 2.0 diesel vehicles, the catalogue includes the ABS pump Bosch 0265222001 / 0265800001.

Its references include:

• 0 265 222 001,
• 0265222001,
• 0 265 800 001,
• 0265800001,
• 091/28/2/0569,
• 968/18/1/0492.

This unit is listed for Rover 75 from approximately 1999–2004. The full number combination should be compared before purchase.

Rover 75 – Bosch 0265222001 / 0265800006

A very similar Rover 75 ABS assembly uses the same Bosch 0265222001 reference but a different additional number: 0265800006.

The Rover 75 ABS unit 0265222001 / 0265800006 carries:

• 0 265 222 001,
• 0265222001,
• 0 265 800 006,
• 0265800006,
• 180214,
• 282/18/12/1679.

This is an important example of why matching only one Bosch number is not enough. The additional electronic and production references should also be checked.

0265800001 vs 0265800006 – why the final digits matter

Two Rover 75 units can both carry the main Bosch reference 0265222001 while using different associated numbers:

• 0265222001 / 0265800001,
• 0265222001 / 0265800006.

They should not automatically be treated as identical or interchangeable. The complete label from the original vehicle should be used for comparison.

Rover 75 – Bosch 0265224009 / 0265900004

Another Rover 75 version available in the catalogue is the Rover 75 ABS pump Bosch 0265224009 / 0265900004.

The main references are:

• 0 265 224 009,
• 0265224009,
• 0 265 900 004,
• 0265900004.

This unit belongs to a different Bosch number family than the 0265222001 versions and should therefore be identified independently.

Rover ABS – Bosch 0265216519 / 0273004247

The catalogue also contains the Rover ABS pump Bosch 0265216519 / 0273004247.

Its principal references are:

• 0 265 216 519,
• 0265216519,
• 0 273 004 247,
• 0273004247.

If your original unit carries these numbers, compare the complete label before ordering.

Bosch numbers used on Rover ABS pumps

Current Rover products in the catalogue include several Bosch number families:

• 0265216519,
• 0265216684,
• 0265222001,
• 0265224009,
• 0273004247,
• 0273004397,
• 0265800001,
• 0265800006,
• 0265900004.

The shared Bosch prefix indicates a number family only. The complete ten-digit reference must be checked.

ABS pump number and ABS control module number

A complete ABS assembly may carry more than one useful identification number. One reference may identify the hydraulic assembly while another identifies the attached electronic controller or a particular production version.

For this reason, the best search method is to use a combination such as:

• 0265216684 + 0273004397,
• 0265222001 + 0265800001,
• 0265222001 + 0265800006,
• 0265224009 + 0265900004,
• 0265216519 + 0273004247.

Common symptoms of an ABS system fault in a Rover

Possible symptoms can include:

• ABS warning light remaining on,
• traction or stability-system warning where fitted,
• ABS function unavailable,
• loss of communication with the ABS controller,
• internal ABS control-unit fault codes,
• hydraulic pump or valve-related fault codes.

These symptoms do not automatically prove that the ABS pump is defective.

ABS warning light – is the pump always faulty?

No. Before replacing the complete ABS assembly, it is worth checking other possible causes such as:

• wheel-speed sensors,
• sensor wiring,
• ABS power supply,
• ground connections,
• fuses and relays,
• electrical connectors,
• vehicle communication wiring.

Diagnostic fault codes and live sensor data can help determine whether the problem is in the ABS pump, electronic controller or another part of the vehicle.

No communication with the Rover ABS module

If a diagnostic tester cannot communicate with the ABS controller, check the module's power supply and communication circuit before assuming that the electronics have failed.

Useful checks include:

• constant power supply,
• ignition supply where applicable,
• ground points,
• fuses,
• connector pins,
• corrosion or moisture,
• communication wiring.

Does a replacement Rover ABS pump require coding?

Do not assume that every Rover ABS pump requires the same coding procedure.

Requirements depend on the particular ABS system and vehicle. A correctly matched replacement may require fewer configuration procedures than a different system, while some applications may require diagnostic functions after installation.

The exact procedure should therefore be confirmed for the vehicle and complete ABS part number.

Does the brake system need bleeding after replacing the ABS pump?

Replacing a complete hydraulic ABS assembly normally involves opening the brake-fluid circuit. The system must therefore be bled correctly after installation.

Depending on the ABS design and workshop procedure, diagnostic equipment may also be used to operate the pump or valves during bleeding.

Because the ABS hydraulic unit is part of the braking system, installation should be carried out by a qualified workshop.

Can only the electronic ABS controller be replaced?

On some systems the electronic controller can be separated from the hydraulic block. Whether this is appropriate depends on the design, the source of the fault and the exact matching numbers.

If only the electronic section is required, see our ABS / ESP / ASR electronic control units.

If the hydraulic section, pump motor or complete assembly is required, a complete ABS pump is the appropriate category.

How to search for a Rover ABS pump by part number

Useful search phrases include:

• Rover 25 ABS pump 0265216684 SRB101210,
• Rover 25 ABS module 0273004397,
• Rover 75 ABS pump 0265222001 0265800001,
• Rover 75 ABS pump 0265222001 0265800006,
• Rover 75 ABS module 0265224009 0265900004,
• Rover ABS pump 0265216519 0273004247.

Searching by two or more numbers from the original unit is normally more precise than searching only for “Rover ABS pump”.

Selected Rover ABS pumps

• Rover 25 – Bosch 0265216684 / SRB101210 / 0273004397
• Rover 75 – Bosch 0265222001 / 0265800001
• Rover 75 – Bosch 0265222001 / 0265800006
• Rover 75 – Bosch 0265224009 / 0265900004
• Rover – Bosch 0265216519 / 0273004247

Related ABS and electronic categories

• Complete ABS Pumps
• ABS / ESP / ASR Electronic Control Units
• Bosch Automotive Electronics
• Electronic Car Parts

ABS pumps for other vehicle makes

If you are looking for a unit for another vehicle brand, you can also browse:

• Opel ABS Pumps
• Ford ABS Pumps
• BMW ABS Pumps
• Audi ABS Pumps

How to confirm compatibility before ordering

If you are unsure which Rover ABS pump is correct, contact Auto24Parts.

For compatibility verification, send:

• a clear photo of the complete original ABS assembly,
• a close-up photo of the Bosch and Rover numbers,
• all numbers from the hydraulic block,
• all numbers from the electronic controller,
• Rover model,
• production year,
• engine version if known.

The complete number combination from the original ABS pump is the safest basis for selecting a replacement.

Ordering, Payment, Delivery and Returns

Ordering information is available in our How to Buy guide. Payment options are listed under Secure Payment Methods, while shipping information can be found on the Shipping & Delivery page.

Current information about returns, complaints and warranty is available under Returns, Warranty & Complaints.

FAQ – Rover ABS Pumps and Control Modules